Bandit 2290 Скачать руководство пользователя страница 72

Страница: 72 / 136

Bandit

MODEL 2290

MAINTENANCE

ADJUSTING INFEED CONVEYOR CHAIN TENSION

1. Follow all pre-maintenance shut down procedures.

2. The infeed chain is tightened or loosened by moving the idler conveyor wheel (located at the end on the

conveyor). See Figure 2.

3. Loosen the bearing adjuster mounting bolts.

4. Loosen the eye bolt jam nuts and adjust the idler conveyor out to tighten the conveyor chain or adjust the

idler conveyor wheel in to loosen the conveyor chain..

5. Be sure that the bearings on both sides are tensioned the same and that the infeed conveyor chain is

running straight.

6. Stand at the end of the conveyor and look down under the infeed chain. The infeed chain should have a

clearance of 1/4” to 3/8” (6 - 10 mm) from the conveyor bed in the middle between the conveyor wheels.

See Figure 1.

7. Running the infeed conveyor chain too loose may cause premature wear and running the infeed

conveyor chain too tight may cause premature failure.

8. When adjustment is finished be sure to tighten the bearing or bearing adjuster bolts and nuts

INFEED MAINTENANCE

Figure 1

VIEW LOOKING AT END OF CONVEYOR

Conveyor

Bed

Infeed chain should

have 1/4” to 3/8”

(6 - 10 mm) of

clearance from the

conveyor bed in the

middle between the

conveyor wheels.

DANGER

Before attempting any type of maintenance, disengage clutch, wait for the disc/drum to come to a complete

stop, turn off engine, remove the ignition key, make sure the ignition key is in your possession, install the

disc/drum lock pin, wait 2 minutes and then disconnect the battery.

Содержание 2290









































































































































Результаты поиска

Содержание 2290

Отзывы:

Бренды по названию

Популярные бренды

Bandit 2290, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание 2290

Отзывы:

Бренды по названию

Популярные бренды