Bandit 2290 Скачать руководство пользователя страница 86

Страница: 86 / 136

Bandit

MODEL 2290

The Bandit is equipped with a very efficient, simple

hydraulic system. Each component is capable of

withstanding a specified PSI (bar) and still operate

for a very long time.
If the simple rules mentioned below are followed, the

hydraulic components will last for years:

• If the Bandit’s hydraulic system is kept clean and

the hydraulic pressures are not increased beyond

the specified PSI (bar), the maximum use and life

should be received from the Bandit chipper hydraulic

system.
• If a problem is encountered, it will more than likely

be located in the relief valve or something as simple

as belts or clutch slipping, check these first.

•

Do not close the optional hydraulic shut-off valve

for more than 3 to 4 seconds. Hydraulic shut-off

valve handle must be completely turned on (in line

with hose) at all times unless checking hydraulic

pressure. Pressure gauge should be safely stored

and installed only when checking pressure. Follow

above instructions or this will cause unwarranted

damage to the hydraulic components.
• Never close the ball valves on the hydraulic

tank suction ports (if equipped) while the machine

is running, this will ruin the hydraulic pump and

components.
•

Some component manufacturers require different

specific hydraulic lubrication, such as gear boxes,

undercarriage drives, etc. Refer to their manuals and

maintenance section of this manual.

HYDRAULICS

After the initial start-up of the machine and after any replacement of hydraulic components, that fittings

and hoses should be re-checked for leaks and clearances.

CAUTION

THE BANDIT HYDRAULIC SYSTEM

HYDRAULICS

• After you have operated a new machine for

approximately an hour shut down the machine and

recheck all hydraulic fittings for tightness and leaks.

• Avoid hydraulic pump cavitation. Low oil levels

or cold start-ups will cause the hydraulic pump to

cavitate. Cavitation will ruin the pump and possibly

the entire hydraulic system. Cavitation only has to

happen once. This will start the pump on its way to

ruin. Allow hydraulic system to turn slowly for several

minutes in cold weather in order for hydraulic system

to warm up. Cavitation is not covered under warranty.
• Do not increase the feedwheel relief valve settings

beyond specified PSI (bar). This will cause damage

to hydraulic components. Do not set any other

hydraulic component past it’s specified pressure or

this will cause damage to the hydraulic components.
• Keep hydraulic oil clean. Dirty oil will cause

excessive wear and loss of hydraulic power.
•

Replace the hydraulic oil filter(s) after first 10 hours

and with each 400 hours of operation or 3 months.
• Replace hydraulic oil & suction screen(s) at least

once yearly. This is also a very good time to flush

and clean the tank. Replace hydraulic oil immediately

if it is contaminated or looks “milky”. See page

79 - 80

for hydraulic oil requirements.

Содержание 2290









































































































































Результаты поиска

Содержание 2290

Отзывы:

Бренды по названию

Популярные бренды

Bandit 2290, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание 2290

Отзывы:

Бренды по названию

Популярные бренды