manualshive.com logo in svg

Bandit 2290, Инструкция по эксплуатации и каталог запасных частей

Поделиться
Скачать
Bandit 2290 Скачать руководство пользователя страница 33

Bandit

29

Copyright 8/19

MODEL 2290

Inside of Cab (if equipped)

Control Panel

  Follow the daily start-up and maintenance check list before starting the machine. Before starting the engine 

make sure that the clutch is not engaged. Turn the battery disconnect switch to the on position. Make sure the 

engine kill switch is not depressed. Make sure the chipper hood engine disable switch is plugged together.  

Turn the ignition switch one stop to the ON position. This will turn on the electrical fuel pump and the rest of 

the electrical system. Then turn the  ignition switch all the way to the right and hold until the engine starts.  

There will be a fi ve second delay, during this time a beeping sound will be heard alerting anyone near the 

machine that it is starting. Also the temperature overheat light will cycle letting you know that it is working.

  Some engines have a pressure override switch wired into their systems. In this case, depress the  pressure 

override button and turn the ignition switch all the way to the right, now hold both until the engine starts. Once 

there is oil pressure the override button may be released.

1.  Follow the daily start-up and maintenance check list before starting the machine.
2.  Turn the ignition key to the on position.
3.  Ensure the machine e-stops are not activated, if equipped.
4.  Put the machine in the radio mode on the control panel.
5.  Put the engine in the idle mode on the control panel.
6.  Ensure switches and paddles are in neutral positions on the radio remote.
7.  Ensure the red e-stop button on the radio remote is depressed.
8.  If it’s a track machine, press the high / low switch to low on the radio remote.
9.  Twist and release the red e-stop button on the radio remote. The yellow active light on the radio remote 

will fl ash.

 The green link light on the radio remote receiver will light.

10. Now the engine is ready to be started.

CONTROLS

STARTING THE MACHINE

REMOTE STARTING PROCEDURE

Содержание 2290









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды