Bandit 2290 Скачать руководство пользователя страница 78

Страница: 78 / 136

Bandit

MODEL 2290

The female splines in the bearing block need to be packed with an EP-2 Lithium type grease every six

months or every 1000 hours. To do this, unbolt the hydraulic pump from the bearing block and slide the

hydraulic pump out of the bearing block. There is no need to loosen or remove the hydraulic lines. Once the

hydraulic pump is removed from the bearing block, inspect the internal splines of the bearing block and the

external splines of the hydraulic pump. The tops of the splines should be fl at. If the splines are pointed, they

are wore and need to be replaced. If the splines are good, pack the internal splines of the bearing block with

an EP-2 Lithium type grease, reinstall the hydraulic pump, and bolt the hydraulic pump to the bearing block.

The fl uid in the bearing block needs to be checked weekly and kept full with an 80W/90 type gear lube.

See the Weekly Maintenance for the capacity, if needed.

Parts may not be exactly as shown.

NOTICE

SERVICING BEARING BLOCK

INTERNAL SPLINES OF

THE BEARING BLOCK

EXTERNAL SPLINES OF

THE HYDRAULIC PUMP

BEARING BLOCK

HYDRAULIC PUMP

MAINTENANCE

Содержание 2290









































































































































Результаты поиска

Содержание 2290

Отзывы:

Бренды по названию

Популярные бренды

Bandit 2290, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание 2290

Отзывы:

Бренды по названию

Популярные бренды