manualshive.com logo in svg

Bandit 2290, Инструкция по эксплуатации и каталог запасных частей

Поделиться
Скачать
Bandit 2290 Скачать руководство пользователя страница 93

Bandit

89

Copyright 8/19

MODEL 2290

INFEED HOPPER COMPONENTS

LOCATION 

PART NUMBER 

DESCRIPTION

Nuts, bolts, washers, and all other components can be ordered by physical description.

NOTICE

2290 TRAILER INFEED

1.   

249-2000-28 

Rear Bumper Assembly

2.   

900-1906-33 Bearing

3.   

900-4902-75 

Adjuster Eye Bolt 5/8” x 6”

4.   

249-2000-08 

Infeed Conveyor Idler Wheel Assembly

5.   

249-3001-06 

Infeed Conveyor Trap Door

6.   

259-2000-58 

Infeed Conveyor Drive Wheel Assembly 

7.   

900-1915-56 

Infeed Conveyor Drive Bearing

8.   

955-0501-47 

Infeed Conveyor Chain Assembly (Paddles 47 Links) 

9.   

900-1914-58 

Infeed Chain Drive Bushing 

10.  

900-1915-53 

Infeed Chain Drive Sprocket

11. a. 

900-1922-86 

Infeed Drive Chain (Includes b. & c.) 

b. 

900-1913-26 

Infeed Drive Chain Master Link 

c. 

900-1913-27 

Infeed Drive Chain Half Link

12. a. 

900-1922-85 

Infeed Drive Chain (Includes b. & c.) 

b. 

900-1913-26 

Infeed Drive Chain Master Link 

c. 

900-1913-27 

Infeed Drive Chain Half Link

13.  

900-1915-55 

Bottom Feedwheel Drive Bushing

14.  

259-2002-72 

Conveyor Drive Gear Box Mount 

15.  

900-3942-59 

Gear Box

16.  

900-6907-69 Gasket

17.  

900-3943-57 

Hydraulic Motor (Infeed/Bottom Feedwheel)

18.  

259-2000-84 

Yoke Stop Assembly

19.  

920-300330 

Yoke Support Top

20.  

249-2000-27 

Top Feedwheel Assembly

21.  

900-3925-07 

Yoke Lift Cylinder

22.  

937-300285 

Yoke Slide

23.  

900-1915-54 

Top Feedwheel Driven Sprocket

24.  

259-2000-54 

Chain Guard Assembly 

25. a. 

900-1922-81 

Top Feedwheel Drive Chain (Includes b. & c.) 

b. 

900-1910-16 

Master Link 

c. 

900-1910-15 

Half Link

26.  

900-1903-43 

Top Feedwheel Drive Bushing

27.  

900-1907-97 

Top Feedwheel Drive Sprocket 

28.  

259-1001-70 

Top Drive Mount Assembly

29.  

900-3906-29 

Top Feedwheel Hydraulic Motor

30.  

900-1902-42 

Yoke Cylinder Bushing

31.  

259-2000-10 

Top Yoke Assembly

32.  

900-3928-16 

Yoke Lock Cylinder

33.  

977-305502 

Yoke Lock Pin

34.  

259-2000-60 

Yoke Lock Pin Assembly

35.  

249-2000-04 

Bottom Feedwheel Assembly

36.  

249-2000-01 

Trap Door Assembly 

37.  

955-300086 

Lock Pin 

38.  

249-3009-77 

Chain Drive Cover Plate 

Содержание 2290









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды