B&D Controll-A-Door Secure SDO-6 Скачать руководство пользователя

Страница: 21 / 24

Parameter

Value options = Indicated by brightness of main light

(DEFAULT parameter underlined)

Name

Flashes

MARGIN

0.7A

0.9A

1.2A

1.5A

2.0A

PE AUTO-CLOSE

OFF

15sec

30sec

60sec

90sec

AUTO-CLOSE

OFF

15sec

30sec

60sec

90sec

120sec

LIGHT TIMER

30sec

60sec

90sec

120sec

180sec

240sec

B - Adjustment Mode Instructions

a. Press the MODE button repetitively until the GEAR

LED starts flashing.

b. Referring to the table below, select the desired parameter using the OPEN

and CLOSE

buttons and

observing the number of flashes on the GEAR

LED. The selected parameter’s value is indicated by the main

light’s brightness.

c. Press STOP / SET button to start editing the parameter’s value. The TRANSMIT

LED will turn on when editing is

active.

d. Use the OPEN

and CLOSE

buttons to step through the available options. The light’s brightness will change

accordingly.

e. Press STOP / SET button to save the parameter’s new value or press MODE to leave the value unchanged.

f. Continue from a. above to select another parameter or press MODE to exit adjustment mode.

D - Battery Functions

a. Holding the STOP button for 10secs when running from battery backup will shut the PCB down so as to reduce

battery current consumption to a minimum.

b. Holding the STOP button for 4secs when a battery is fitted and running from mains power will cause the controller to

test the battery state to determine if it is disconnected / open circuit, missing, faulty or ready.

The Safety Obstruction Force is calculated automatically during

setup. Adjusting this is normally only necessitated by environmental

conditions such as windy or dusty areas, and areas with extreme

temperature changes.

To Increase / Decrease Force Pressure

a. Press the MODE button repetitively until the GEAR

LED is

flashing.

b. The LED will start flashing with one flash every second.

c. Press the STOP / STEP button and the MODE button LED and the

TRANSMIT

LED will be lit and the GEAR

LED will flash once

every second.

d. By pressing the OPEN button

will increase the force pressure

and CLOSE button

will decrease the force - Main light will dim

or brighten as the pressure is decreased or increased.

e. Press STOP / SET button to save the new value. (Refer to

Appendix B for margin settings)

f. Test the force again as per Testing Close Cycle and Testing Open

Cycle.

C - Adjusting Force Margins

Controll-A-Door

Installation instructions

Содержание Controll-A-Door Secure SDO-6

























Результаты поиска

Содержание Controll-A-Door Secure SDO-6

Отзывы:

Похожие инструкции для Controll-A-Door Secure SDO-6

Бренды по названию

Популярные бренды

B&D Controll-A-Door Secure SDO-6, Руководство по установке

Результаты поиска

Содержание Controll-A-Door Secure SDO-6

Отзывы:

Похожие инструкции для Controll-A-Door Secure SDO-6

Бренды по названию

Популярные бренды