manualshive.com logo in svg

B&D Controll-A-Door Secure SDO-6, Руководство по установке, Страница: 23 / 24

Поделиться
Скачать
B&D Controll-A-Door Secure SDO-6 Скачать руководство пользователя страница 23

G - Setting up Tilt Door

Prior to limit set up, the opener can be set to J-Type Tilt Profile. This process allows the opener to pre-set to J-Type settings 

where the limit is not greater than 1500mm. If J-Type is selected, the speed is customised and cannot be changed. 

a. Press the MODE button repetitively until the GEAR 

 LED starts flashing.

b. Press and hold STOP / SET button for 2 seconds to check the door type, until the main courtesy light turns solid ON 

or OFF.

 

•

Main courtesy light ON - Tilt type (J-Type only)

 

•

Main courtesy light OFF - Sectional type

c. Press and hold STOP / SET for 6 seconds to change the door type, until the main courtesy light turns solid ON or 

OFF. If required, repeat step b to check the door type selected.

d. Press MODE button to exit the door selection mode. Proceed to Section 12 to set the limits.

23

Controll-A-Door

 

®

 - 

Installation instructions

Содержание Controll-A-Door Secure SDO-6

























Отзывы:

Нет отзывов