Bally ProSlot 6000, Настройка и эксплуатация

Страница: 41 / 444

©2004 Bally Gaming and Systems
2-41
ProSlot
®
6000
| - Revised, || - New
#11 - Game Optioning
Game Optioning is set from Diagnostic Function #11.
See the Machine Options section (page 2-14) for
detailed instructions on accessing and setting options.
#10 - Payout Test
The Payout test confirms that reel symbol combinations
match the game's pay table as it appears on the feature
glass. By positioning the reel symbols on the payline,
entering a wager, and pressing
SPIN
, the win amount
appears in
WIN PAID
. I t should match the glass for the
same winning combination.
Press and release the
TEST
button until the message
10 d appears in
WIN PAID
, indicating the Payout test
is selected. Press and hold
CHANGE
. The message “rl
1” appears in
CREDIT
, indicating reel one is selected.
While holding
CHANGE
, press the
SPIN
button. Reel one
moves to the next stop position. Release and press
SPIN
( still holding down the
CHANGE
button) until the
desired reel symbol lines up on the pay line, then
release the
CHANGE
button. Repeat to select positions
for the remaining reels.
After selecting the reel positions, press
BET ONE
to
select the number of credits to wager. Press
SPIN
.
The
CREDIT
display shows the win for the reel-symbol
combination, the wager, and the credits to be paid
from the hopper.
Repeat the procedures above to confirm payouts for
any reel combination and wager.
Diagnostic Tests and Functions
#12 - Peripherals Test
Test #12 allows the operator to evaluate peripheral
devices on the ProSlot
®
6000.
The results of the test are indicated in the Message
Center. Each value shows for two seconds before
automatically advancing to the next item. The
Operator may also manually advance by successively
pressing
BET MAX
, or may pause the display by pressing
and holding
SPIN
.
To access, press and release the
TEST
button until 12
d appears in
WIN PAID
, indicating the Peripherals test
is selected.
Win Paid Credit Device
12 1 D Value DIP Switch DS1 in Hexadecimal
12 2 D Value DIP Switch DS2 in Hexadecimal
12 3 D Value DIP Switch DS3 in Hexadecimal
12 4 D Value Battery Voltage in Hexadecimal
12 5 D - 0 Bet One Sound at Current Volume Level
12 5 D - 1 Bet Max at Full Volume (Alarm)
12 6 D Value Current Real Time Clock
12 7 D E400 Expanded EPROM Memory Status for 2MG
The third digit in
WIN PAID
shows the identification
number for each item in this test. For the first item,
121d appears in the display. The last two digits of the
CREDIT
display show the settings of DIP Switch DS1
in hexadecimal representing the value of the eight
switches. Refer to the following table to determine
the switch settings:
SW 1 & 5 SW 2 & 6 SW 3 & 7 SW 4 & 8
Hex Digits
1st & 2nd
ON ON ON ON 0
OFF ON ON ON 1
ON OFF ON ON 2
OFF OFF ON ON 3
ON ON OFF ON 4
OFF ON OFF ON 5
ON OFF OFF ON 6
OFF OFF OFF ON 7
ON ON ON OFF 8
OFF ON ON OFF 9
ON OFF ON OFF A
OFF OFF ON OFF B
ON ON OFF OFF C
OFF ON OFF OFF D
ON OFF OFF OFF E
OFF OFF OFF OFF F
The first digit represents switches 5-8. The second
digit is switches 1-4. For example, a value of 11 for
DS1 can be interpreted as 1 = switches 5 through 8
=
OFF
,
ON
,
ON
,
ON
; 1 = switches 1 through 4 =
OFF
,
ON
,
ON
,
ON
. T he value 11 indicates that the machine is
configured for SAS
®
EFT protocol v4.x or v5.x with
no bonus. Refer to the DS1 Switch Communication
Protocol table (page 2-9).
DIP Switch settings for DS2, display
122d , and DS3,
display 123d, can be determined in a similar manner.
When 125d appears,
CREDIT
shows 0 in the last digit.
The diagnostic function sends the
BET ONE
sound
to the speaker at the current volume level. After
two seconds, the last digit of
CREDIT
shows 1 . The
diagnostic function then sends the alarm sound, which
is the
BET MAX
sound at full volume. It requires jumper
JW18 to be installed on the MPU board. Refer to the
Jumper table (page 2-9).
Note: Jackpot signals through
connector J13 are disabled to prevent
false progressive win lockups. See
Option 80 (page 2-13).