Peripherals
©2002 Bally Gaming and Systems
8-5
Peripherals
Coin Acceptors
Coin Mechanisms, Inc. • 400 Regency Drive,
Glendale Heights, Illinois 60139-5128 • Toll
Free: (800) 323-6498 Phone: (630) 924-7070
Fax: (630) 924-7088 • www.coinmech.com
CC-16
Power Requirements:
fixed VDC models, 11.5
to 12.5 VDC
Feed Rate: 7 coins per
second (models CC-16,
CC-62, MC-16):
Designed for coin
diameters of .700"
(17.8mm) to 1.575 (40mm). Wide Body model
recommended for coin diameters up to 1.95"
(49.5mm).
Operating temperature recommended: 0
o
to 60
o
C.
Installing the Sample Coin (models CC-16, CC62, MC-
16): Looking at the front of the comparitor, slide (with-
out lifting) the sensor coil assembly to the right. Re-
place the sample coin (or chip) with the desired coin
(or chip) and then carefully release. In most cases, the
coin (or chip) will automatically seat itself. When prop-
erly seated, the coin (or chip) will rest parallel between
the sensor coil assembly and between the ribs on the
rail insert.
Replacing an Existing Mechanical Acceptor (models
CC-16, CC-62, MC-16):
1.
Remove the acceptor.
2.
Disconnect the coin return linkage.
3.
Remove the lockout coil (if used).
4.
In some cases, the comparitor mounting studs may
need to be relocated to meet manufacturer’s
mounting specifications.
5.
Mount comparitor into equipment, ensuring that
coin entry and coin exit are aligned.
Wiring Instructions: The CC-16 printed circuit board
requires a 6-pin JST terminated interface. The con-
nector diagram following denotes the typical voltage
line pinouts to the printed circuit board:
Potentiometer Adjustment (models CC-16, CC-62):
Each comparitor is adjusted to give excellent discrimina-
tion against slugs. However, some high quality slugs may
need a finer adjustment.
1.
Adjust potentiometer clockwise (CW) until high qual-
ity slug is rejected.
2.
Drop good coins to ensure accurate acceptance.
3.
Repeat steps 1 and 3 if necessary. For further poten-
tiometer adjustment procedures, call or fax Coin
Mechanism, Inc.’s service department and request
document #09300072.
Before Turning Power On (models CC-16, CC-62, MC-
16):
1.
Make sure that all connections are properly insulated.
2.
Tuck wire to prevent interference with coin travel or
coil armature movement.
3.
Check the power cord for firm connection to the PC
board.
4.
Make sure the comparitor is mounted securely in the
equipment.
5.
Check the entry chute alignment by inserting the
proper coin. The coin should fall freely, without stop-
ping, through the comparitor and reject out of the
equipment.
After Turning Power On (models CC-16, CC-62, MC-16):
1.
The LED will illuminate when voltage is applied.
2.
Drop good coins. They should be recognized by the
comparitor and accepted.
3.
Repeat step 2 several times to ensure the unit is func-
tioning properly.
CC-16
1. Inhibit input - 12VDC models only
All other models - Triac load
2. Sense output
3. 48 Volt
4. 24 Volt
5. 12 Volt
6. Ground
1
2
3
4
5
6
Содержание ProSlot 6000
