Bally ProSlot 6000, Настройка и эксплуатация

Страница: 10 / 444

SETUP AND OPERATION
2-10
©2004 Bally Gaming and Systems
ProSlot® 6000
| - Revised, || - New
Door Open Detect Circuit
Some jurisdictions require a signal for a door opening
while the machine power is
OFF
. To enable the door
open latch, place the jumper at JW15 in position 1 and
add a jumper at JW17. Default is
OUT
(
OFF
).
MPU Logic Detect Circuit
Some jurisdictions require a signal when the MPU
board assembly is disconnected while the power is
OFF
. To enable the MPU detach latch, place JW15
in position 1 and add a jumper at JW21. Default is
OUT
(
OFF
).
The following table lists 2-pin and 3-pin jumper
selections:
Securing the Machine
Remove the hopper. Mark the center of the stand.
Drill the required mounting, drop chute, and power
cord holes. Using a lifting device, place the machine
on the stand and route the power cord through the
stand hole. Bolt the machine to the stand. Inspect for
loose connectors and verify all printed circuit boards
are firmly seated.
Install Locks
Door, stand, and other high-security locks should be
ordered by the Operator from a reliable lock supplier.
See Module 3 Assemblies, Parts and Hardware for
lock specifications.
Remove the large and small nuts from the lock and
insert the lock into the lock opening. Check the lock
for proper orientation before securing. Secure the lock
with the large nut. Place the cam stop on the lock
cylinder. Attach the lock cam to the shEFT and verify
that it moves in the correct direction. Secure the lock
cam with the washer and small nut.
Lock
Cam Stop
Force Nut
Cam
Washer
Nut
Typical Lock and Cam Assembly
Installing the Machine (cont.)
Setup
Plug the line cord into a grounded power source, but
do not turn the machine on.
MPU Jumper Selections
Battery Enable
The Lithium battery may be disabled for shipping or
storage. To enable the battery, locate jumper JW20 left of
the battery and place the jumper across the two pins.
Warning: Attempting to charge
Lithium batteries can cause them
to explode. Replace failed batteries
with Bally part E-00628-0023 or its
equivalent.
Jumper Shipping
Position
Purpose Pos. 1 Pos. 2
JW1 Out (Off) External Antenna In Out
JW2 2 Meg Eprom Size 2 Meg 4 Meg
JW3 32K Personality Eprom Size 32K 64K
JW4 VBB RAM Power Select +5 VBB
JW5 RS232 RX Port 3B RS422 RS232
JW6 Out (Off) DSR Input 3A In Out
JW7 Out (Off) DTR Output 3A In Out
JW8 RS232 Link RX RS232 RS422
JW9 Enable Link RS422 Enable Disable Enable
JW11 Out (Off) MPU Detect Feature In Out
JW12 In (On) SafeRAM™ Key In Out
JW13 Isol TX Bill Acceptor TX ISOL RS232
JW14 Isol RX Bill Acceptor RX ISOL RS232
JW15 Out (Off) VBB Door Open Latch In Out
JW16 ADC Smart Socket Enable ADC +5
JW17 Out (Off) Door Open w/Power Off
Input
In Out
JW18 Out (Off) Alarm In Out
JW19 In (On) MPU Board Antenna In Out
JW20 Out (Off) Battery In Out
JW21 Out (Off) MPU Backplane Detach
Detect
In Out
1
3
2
Position 1 Position 2
1 2
OUT
1 2
IN
1
3
2
|
|