Bailey NIAO01 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 27

background image

INTRODUCTION

SPECIFICATIONS

1 - 4

I-E96-438A

®

Table 1-4. NIAO01 Termination Module Specifications

Property

Characteristic/Value

Surge Protection

Meets IEEE-472-1974 surge withstand capability test.

1

Wire Size:

Minimum

Maximum

Maximum wire size
when connecting three
wires to a single
terminal

22 gauge.

14 gauge.

One 16 gauge and two 18 gauge wires.

Mounting

Occupies one slot in a standard INFI 90 termination mounting unit.

Environmental:

Electromagnetic/
Radio Frequency
Interference

Ambient Temperature

Relative Humidity

Atmospheric Pressure

Air Quality

No values available at this time. Keep cabinet doors closed. Do not use
communication equipment closer than 2 meters from the cabinet.

0° to 70°C (32° to 158°F).

0% to 95% up to 55°C (131°F) noncondensing.
0% to 45% up to 70°C (158°F) noncondensing.

Sea level to 3 km (1.86 miles).

Bailey equipment should be operated and stored in a noncorrosive environment.

Cooling Requirements

No cooling is necessary when used in Bailey cabinets and operated within
stated environmental limits.

Certification

CSA certified for use as process control equipment in an ordinary
(nonhazardous) location.

NOTE: 1. Do not use the NKTM01 cable when compliance with IEEE-472-1974 is necessary.

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.

«
...
10
11
12
13
14
...
»

Содержание NIAO01




























Отзывы:

Нет отзывов

Похожие инструкции для NIAO01

Бренд: National Instruments Страницы: 8

Бренд: Easy wave Страницы: 2

Бренд: FingerTec Страницы: 35

Бренд: Ascon tecnologic Страницы: 4

GreenKeeper 212

Бренд: Toro Страницы: 39

Бренд: Parkside Страницы: 124

Бренд: XtendLan Страницы: 22

Бренд: urmet domus Страницы: 22

AutoLift AL-6000S2

Бренд: AAQ Страницы: 36

Бренд: CAME BPT Страницы: 16

Бренд: Naya Страницы: 11

Бренд: Rain Bird Страницы: 5

Бренд: Invacare Страницы: 21

EASY CLEAR EQ-12-TH

Бренд: Bunn Страницы: 2

Бренд: Elo Touch Solutions Страницы: 3

Water Quality System EQHP-TWIN 108SP

Бренд: Bunn Страницы: 2

Бренд: Rain Bird Страницы: 8

AIR ADJUST 2940

Бренд: Yetter Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды