manualshive.com logo in svg

Bailey NIAO01, Инструкция

Поделиться
Скачать
Bailey NIAO01 Скачать руководство пользователя страница 10

INTRODUCTION

MODULE DESCRIPTION

1 - 2

  

I-E96-438A

®

MODULE DESCRIPTION

The IAO termination module is a single printed circuit board
that uses one slot in an NTMU01 or NTMU02 Termination
Mounting Unit. The IAO termination module has one card edge
connector, P1. It carries the outputs from the analog output
module to the field device through an NKTM01, NKTU02 (PVC
jacket) or NKTU12 (non-PVC jacket) Termination Module
Cable. Field devices connect to the IAO termination module
terminal strip. The dipswitches on the IAO termination module
select the output signal type. The output signal type on the IAO
termination module must match the analog output module.

INSTRUCTION CONTENT

This manual consists of five sections and an appendix.

Introduction

Contains an overview of the features, specifications and a
description of the IAO termination module.

Installation

Describes precautions to observe when handling modules and
setup procedures required before module operation. This sec-
tion also discusses dipswitch settings and installation
procedures.

Maintenance

Provides a maintenance schedule.

Repair/Replacement

Procedures

Details how to replace an IAO termination module.

Support Services

Describes the support services (spare parts, training, docu-
mentation, etc.) available from Bailey Controls Company.

Appendix A

Contains data to connect the termination module to the analog
output module. Appendix A shows the switch settings and
cabling requirements for the analog output module.

HOW TO USE THIS MANUAL

Read this manual through in sequence. Read the installation
section thoroughly. Do the steps in order. Complete all steps in
the installation section before operating the IAO termination
module. Refer to the Table of Contents or Index to find specific
information after the module is operating.

REFERENCE DOCUMENTS

Table 

1-1

 lists the documents referenced in this instruction.

Table 1-1.  Reference Documents

Number

Document

I-E96-206

IMAOM01 Analog Output Module

Содержание NIAO01




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды