manualshive.com logo in svg

Bailey Infi 90 IMEDI01, Инструкция

Поделиться
Скачать
Bailey Infi 90 IMEDI01 Скачать руководство пользователя страница 56

INTRODUCTION

WBPEEUI240759A0   

9 - 1

 

SECTION 9 - SUPPORT SERVICES

INTRODUCTION

Elsag Bailey is always ready to assist in the operation and
repair of its products. Send requests for sales or application
services to the nearest sales or service office. Elsag Bailey can
also provide installation, repair and maintenance contract
services.

REPLACEMENT PARTS AND ORDERING INFORMATION

Order replacement parts through an Elsag Bailey sales or ser-
vice office. Provide the following information:

1. Part description, part number and quantity.

2. Model and serial number (if applicable) and ratings of the
assembly for which the part has been ordered.

3. Elsag Bailey instruction number, page number and refer-
ence figure that identifies the part.

When ordering parts, use part numbers and part descriptions
from equipment manuals. Parts with no commercial descrip-
tion must be ordered from the nearest sales or service office.
Recommended spare parts lists, including prices, on standard
assemblies are available through the nearest sales or service
office.

TRAINING

Elsag Bailey has a modern training facility available for train-
ing your personnel. On-site training is also available. Contact
an Elsag Bailey sales office for specific information and
scheduling.

TECHNICAL DOCUMENTATION

Additional copies of this instruction, or other Elsag Bailey
instructions, can be obtained from the nearest Elsag Bailey
sales office at a reasonable charge.

Содержание Infi 90 IMEDI01


























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды