manualshive.com logo in svg

Bailey Infi 90 IMEDI01, Инструкция

Поделиться
Скачать
Bailey Infi 90 IMEDI01 Скачать руководство пользователя страница 13

INTRODUCTION

INSTRUCTION CONTENT

WBPEEUI240759A0   

1 - 3

 

INSTRUCTION CONTENT

This instruction consists of the following sections and appendi-
ces.

Introduction

Overviews the EDI module. It contains features, a description,
reference documents, and specifications.

Description and

Operation

Explains the theory of module operation.

Installation

Covers handling precautions, switch and jumper settings, and
EDI module installation and connection.

Operating Procedures

Explains how to start up and operate the EDI module.

Troubleshooting

Describes how to check for EDI errors and the corrective
actions to take.

Maintenance

Contains a maintenance schedule for the EDI module.

Repair and Replacement

Procedures

Explains how to replace an EDI module.

Support Services

Provides information about ordering parts from your local
Elsag Bailey sales office. It also explains other areas of support
that Elsag Bailey provides.

Appendix A

Provides IMEDI01 module information necessary to interface
to an Allen Bradley controller (PLC-5E and higher).

Appendix B

Provides IMEDI01 module information necessary to interface
to a Triconex Systems PLC.

HOW TO USE THIS INSTRUCTION

Read this instruction before placing the EDI module in opera-
tion. Refer to the sections in this list as needed for more
information.

1. Perform the steps in 

Section 3

 to install the EDI module.

2. Read 

Section 4

 for function code configuration information.

3. Read 

Section 5

 before placing the EDI module into opera-

tion. 

4. Refer to 

Section 6

 if a problem occurs.

5. Refer to 

Section 7

 for general guidelines for EDI module

maintenance.

6. Refer to 

Section 9

 for procedures to replace a module.

Содержание Infi 90 IMEDI01


























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды