manualshive.com logo in svg

Bailey Infi 90 IMEDI01, Инструкция

Поделиться
Скачать
Bailey Infi 90 IMEDI01 Скачать руководство пользователя страница 12

INTRODUCTION

INTENDED USER

1 - 2

  

WBPEEUI240759A0

®

 

INTENDED USER

This instruction is intended for personnel responsible for
installing, operating, and maintaining the EDI module. Instal-
lation requires an engineer or technician with experience han-
dling electronic circuitry, and is familiar with the INFI 90 OPEN
system and Ethernet networks.

COMPATIBILITY

The IMEDI01 module is compatible with and can be used to
interface the following third-party Ethernet PLCs:

•

Allen Bradley PLC-5E and higher.

•

Triconex Systems Tricon V6 PLC and higher (with Network
Communications Module).

HARDWARE REQUIREMENTS

An IMMFP01, IMMFP02, or IMMFP03 Multi-Function Proces-
sor module with firmware revision G.0 or later is required to
operate the IMEDI01 module.

Additionally, the IMEDI01 module must contain the proper
interface protocol for the third-party Ethernet PLC being inter-
faced. Check the protocol label on the IMEDI01 module to ver-
ify the protocol installed. Refer to the appendices for protocol
identification information.

FEATURES

•

Downloadable firmware residing in FLASH memory.

•

Ethernet connection using TCP/IP communication.

•

Serial engineering and diagnostic port.

•

High performance 32-bit microprocessor running at 25
megahertz.

•

Standard INFI 90 OPEN packaging and power system.

•

Interfaced to process control unit via I/O expander bus.

•

Configuration via standard INFI 90 OPEN function codes.

•

High capacity local data table (over 1,000 points).

•

High data exchange rate (ten megabaud).

Содержание Infi 90 IMEDI01


























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды