background image

 

Main Materials: 
 

Bed ...............................................................................................  .............................. cast iron, ground surface 

 

Bow ..............................................................................................  ........................................................ cast iron 

 

Stand ............................................................................................  .............................................................. steel 

 

Blade drive system……………………………..steel, heat-treated worm driving a bronze worm gear in oil bath 

 

Side blade guides……………………………………………………….ball bearings mounted on eccentric shafts 

 

Rear blade guides ........................................................................  ................................................. ball bearings 

 

Band wheels ................................................................................  ................................................. ball bearings 

 
Dimensions: 
 

Table plate dimensions ................................................................  ........................... 12 x 12 in. (305 x 305mm) 

 

Overall dimensions, assembled .................................................. . ............................................. 48 x 17 x 40 in. 

 

 .....................................................................................................  .............................. (1219 x 432 x 1016 mm) 

 

Overall dimensions, shipping .......................................................  ................................ 51.18 x 19.2 x 44.88 in. 

 

 .....................................................................................................  .............................. (1300 x 488 x 1140 mm) 

 

Stand wheels ...............................................................................  ............................................... 8 in. (203mm) 

 
Weights:

  

 

Net weight ....................................................................................  .......................................... 374 lbs. (170 kg) 

 

Shipping weight ............................................................................  .......................................... 418 lbs. (190 kg) 

 
 
 

The  specifications  in  this  manual  were  current  at  time  of  publication,  but  because  of  our  policy  of  continuous 
improvement, Baileigh Industrial reserves the right to change specifications at any time and without prior notice, without 
incurring obligations.

 

 

Содержание BHVBS-712B

































Отзывы: