Baileigh Industrial BHVBS-712B, Инструкция по эксплуатации и каталог запасных частей

Страница: 2 / 32

1.0 IMPORTANT SAFETY
INSTRUCTIONS
Read and understand the entire instruction
manual before operating machine.
This band saw is designed and intended for use
by properly trained and experienced personnel
only. If you are not familiar with the proper and
safe operation of a band saw, do not use until
proper training and knowledge have been
obtained.
WARNING – To reduce risk of injury:
a. Wear eye protection.
b. Do not remove jammed cut off pieces until
blade has stopped.
c. Maintain proper adjustment of blade
tension, blade guides, and thrust bearing.
d. Adjust upper guide to just clear workpiece.
e. Secure workpiece firmly against table.
1. Read and understand the warnings posted on
the machine and in this manual. Failure to
comply with all of these warnings may cause
serious injury.
2. Replace warning labels if they become
obscured or removed.
3. Do not use this band saw for other than its
intended use. If used for other purposes, JET
disclaims any real or implied warranty and holds
itself harmless from any injury that may result
from that use.
4. Always wear ANSI Z87.1 approved safety
glasses or face shield while using this band
saw. (Everyday eyeglasses only have impact
resistant lenses; they are
not safety glasses.)
5. Before operating this machine, remove tie,
rings, watches and other jewelry, and roll
sleeves up past the elbows. Do not wear loose
clothing. Confine long hair. Non-slip footwear or
anti-skid floor strips are recommended. Do not
wear gloves.
6. Wear hearing protection (plugs or muffs) during
extended periods of operation.
7. Do not operate this machine while tired or under
the influence of drugs, alcohol or any
medication.
8. Reduce the risk of unintentional starting. Make
sure switch is in off position before plugging in.
9. Make certain the machine is properly grounded.
10. Make all machine adjustments or maintenance
with the machine unplugged from the power
source.
11. Remove adjusting keys and wrenches. Form a
habit of checking to see that keys and adjusting
wrenches are removed from the machine
before turning it on.
12. Keep safety guards in place at all times when
the machine is in use. If removed for
maintenance purposes, use extreme caution
and replace the guards immediately after
completion of maintenance.
13. Check damaged parts. Before further use of the
machine, a guard or other part that is damaged
should be carefully checked to determine that it
will operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or
replaced.
14. Provide for adequate space surrounding work
area and non-glare, overhead lighting.
15. Keep work area clean. Keep floor around the
machine free of scrap material, oil and grease.
Cluttered areas and benches invite accidents.
16. Keep visitors a safe distance from the work
area. Keep children away.
17. Make your workshop child-proof with padlocks,
master switches or by removing starter keys.
18. Give your work undivided attention. Looking
around, carrying on a conversation and “horse-
play” are careless acts that can result in serious
injury.
19. Maintain a balanced stance at all times so that
you do not fall into the blade or other moving
parts. Do not overreach or use excessive force
to perform any machine operation.
20. Use the right tool at the correct speed and feed
rate. Do not force a tool or attachment to do a
job for which it was not designed. The right tool
will do the job better and more safely.
21. Use recommended accessories; improper
accessories may be hazardous.
22. Maintain tools with care. Keep saw blades
sharp and clean for the best and safest
performance. Follow instructions for lubricating
and changing accessories.
23. Turn off the machine before cleaning. Use a
brush to remove chips or debris — do not use
your hands.
24. Do not stand on the machine. Serious injury
could occur if the machine tips over, or if the
cutting tool is unintentionally contacted.