the
LARGE-SIZE
parasol
3
3.1 During and upon basic erection the umbrella corpus to be in its soft-wrapped condition still (either plastic-hose
material or optional reusable protective cover wrapping)
!
3.2 Just temporarily engage the pole in its footing component in concrete to ensure that the structure will not be
lifted out of its footing again (e.g. by a sudden gust) during the following working steps.
3.3 To remove the protective soft wrapping material:
3.31
Use a free-standing safety stepladder secured by a second person standing on the ground. Set it up across
and closest to the now standing umbrella structure.
3.32
Use the white/clean protective gloves from the structure’s accessory kit coming with to prevent the fabric
corpus from getting dirtied unintendedly.
3.33
If the fabric corpus is in standard plastic hose wrapping: Manually untie (don’t use scissors, knife or any
other tool –
take note of the specific ”Take care!” warning notice visible and legible on or through either
plastic
hose or protective cover packing material
!) the fabric ribbon bow at the bottom of the hose
wrapping so that the hose regains its full width at the bottom.
3.34
If the fabric corpus is in a reusable protective cover: Untie its cords at the bottom.
3.35 Initially from the ground, then from your rising position on the ladder, gradually shift hose material or
cover up as much as practicable. Eventually, from your highest position required on the ladder, pull hose
or cover off the top of the umbrella structure. Recommendation: Store up hose or cover for reusage when
required.
3.4 Both the cone-shaped solid top cover (apex element) and the (white) screw-ball to be taken from the accessory
package coming with every Jumbrella. The larger & heavier models come with a factory-fixed crane eyelet,
which has to be removed first. Put the solid cover on top of the structure. Make sure it touches down and
engages distinctly. Insert the screw-ball or eyelet, respectively through the central opening in top of the cover
(receiving taphole right underneath), screw in and tighten it so that it cannot unloosen again by itself. Remove
the ladder since it is no longer required from now on.
3.5 Unlock and take both cylinder locks out of the tension latches. Partly (by some 30 degrees off its down position)
open the left-hand latch so that it gets free from the blocking device (active only with the closed umbrella) on
the major pole. Leave the left-hand latch in this partly opened/spread position.
3.6 Remove the Bahama Swiftbelt (buckle harness) from the umbrella corpus. With your hands clean (or wearing
white protective gloves from the umbrella’s
accessory package), manually unwind the fabric layers of the
membrane (wound all about the frame body) to neutral i.e. unwound & untwisted. The membrane should now
”hang” relaxed for the following workings steps:
3.7 Slightly lift all 8 [10 or 12] rib (arm) ends off the structure to release the folding frame from its potential dead-
centre configuration. From your
operator position
(facing the empty lock ports in both latches): Hook your finger
tips under 2 extreme arm (rib) ends next to each other, and pull them towards your position to unfold the
Jumbrella. With traditional i.e. valance-equipped membrane editions, interrupt unfolding in order to check
valance shields not twisted (not jamming) about arm (rib) ends. If one or more of them twisted, clear them
down before recontinuing to unfold.
3.8 Manually unfold further up to a 70 to 80 percent OPEN canopy configuration that allows you to get under it
comfortably into your new position right in front of the major pole: Due to its mass centre-balanced kinematic
design, the canopy stays put, it doesn’t recollapse by itself. With both hands on shift the ”carriage” (bearing
tensions latches, sliding on major pole) up further, hold it in position with your left, open the RIGHT-hand
tension latch up widely so to be able to engage its spring clip in the counter-catch overhead. Turn the right-
hand latch down by approx. half its way or as required to enable you to also engage the left-hand spring clip in
its counter-catch overhead. Thereupon, wholly turn down both latches at a time: When both latches have been
turned down wholly, the canopy has reached 100 percent of its factory-predetermined amount of induced
overall tension required!
Содержание Jumbrella
