BAHAMA Jumbrella страница 43 Скачать руководство пользователя | Manualshive

Страница: 43 / 56

background image

Bahama

GmbH

made in Germany

Installation Manual | LED

Tel +49 (0)2265 998 0

Gewerbeparkstrasse 34

Edition: 10|2020

D-51580 Reichshof

Instruction Manual | LED-Lighting

Contents:

1.

Teaching the remote control and connecting up to 4 umbrellas to one remote control

2.

Remote control functions

3.

Connection via Wifi | App

1.

Teaching the remote control and connecting up to 4 umbrellas to one

remote control

1.

Connect the power supply to the
umbrella.

2.

Switch on the remote control.

3.

Select and press the zone to which
the umbrella shall be programmed.

4.

Press the learning switch on the LED
controller which is installed on the
umbrella center pole.

→

The LED strips flash.

5.

Select the desired light color using
the color selector on the remote.

To sync more than one umbrella to the remote control, repeat steps 3 through 5.

Several umbrellas can either be synced to one and the same zone or to different zones.

Resetting the controller:
-

Press and hold the learning switch until the LED strips flash and return to white
light.

«
...
41
42
43
44
45
...
»

Содержание Jumbrella

























































Отзывы:

Нет отзывов

Похожие инструкции для Jumbrella

Бренд: 4 Moms Страницы: 21

Бренд: Ballard Designs Страницы: 10

Бренд: Babybee Страницы: 16

Бренд: KidKraft Страницы: 2

Large Classic Toy Box

Бренд: Great Little Trading Страницы: 5

JUTLANDIA TRONDHEIM 3710017

Бренд: Jysk Страницы: 24

Бренд: Bolig Engros Страницы: 11

Бренд: Carena Страницы: 11

Бренд: Carena Страницы: 37

Osborn D71 M20186

Бренд: GRAND RESORT Страницы: 7

Osborn 5pc Dining Set D71 M20180

Бренд: GRAND RESORT Страницы: 7

Бренд: BabyGo Страницы: 52

Бренд: Kiddicare Страницы: 8

Anna Dropside Cot

Бренд: Kiddicare Страницы: 4

Бренд: Kiddicare Страницы: 20

Бренд: Steens Страницы: 21

Бренд: Chicco Страницы: 36

Бренд: Baby Max Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды