BAHAMA Jumbrella Скачать руководство пользователя | Manualshive

Страница: 51 / 56

background image

Edition 09/2020

Bahama GmbH | Gewerbeparkstr. 34 | D-51580 Reichshof

[email protected]

| 0049 (0)2265/998-0 |

|

Manual for heating radiators

4

Switching off the radiators and closing the umbrella

4.1

Switch off the radiators via the remote control (The control lamps light up blue again).

4.2

Check that all radiators have responded and have been switched off.
Note: Should one of the radiators still be in operation, again point the remote control towards it
and press

”off“.

Do

NOT

immediately touch the radiators after switching them off &

do

NOT

immediately close the umbrella.

The radiators require approx. 10-15 minutes until they have sufficiently cooled down.

4.3

Turn the radiators back by 90° into a
vertical position.

4.4

Begin to slowly close the umbrella. Before
completely closing the umbrella, tilt the
radiators by 90° to the right in the
direction of the cable.

WARNING:

The screws of the tilting bracket might come loose after several

opening and closing procedures. In such a case, re-tighten the screws
accordingly.

4.5

The umbrella can now be completely closed. Please make sure that the
radiator bracket is positioned below the spoke supporting beam.

Note: You might have to slide the radiator further down. (This is
especially required for radiators that are mounted to the diagonal
support spokes of rectangular models.)

«
...
49
50
51
52
53
...
»

Содержание Jumbrella

























































Отзывы:

Нет отзывов

Похожие инструкции для Jumbrella

Бренд: Bebe Care Страницы: 8

Joie Excursion Toy Travel Cot

Бренд: Jole Страницы: 6

Бренд: dreambaby Страницы: 3

Бренд: HAMPTON BAY Страницы: 25

SUNNY 45 DR Series

Бренд: Quax Страницы: 17

Deluxe PY71A48A

Бренд: Baby Trend Страницы: 30

FAUX STONE BASE 780-0644A

Бренд: Duro Страницы: 12

Бренд: Badger Basket Страницы: 7

Larkin Toddler Rail

Бренд: The Land of Nod Страницы: 7

Бренд: Inspired by drive Страницы: 8

Universal Squared 3 Tier Changer B-SQCH

Бренд: boori Страницы: 5

Expandable Pioneer

Бренд: boori Страницы: 11

Бренд: Rovo Kids Страницы: 4

Бренд: Bellelli Страницы: 86

Бренд: Badger Basket Страницы: 5

Бренд: Badger Basket Страницы: 5

Emily Love Seat

Бренд: Zest 4 Leisure Страницы: 5

Бренд: Britton Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды