background image

STATUS MODE 

 
  The Status Mode contains the Alarms Tripped screen 
and the Self Test screen. To enter into the Status Mode 
press the MENU key and the following screen will 
appear: 
 
 

PRESS UP FOR CALIBRATION 

PRESS DOWN FOR STATUS 

 
 
  Pressing the DOWN arrow key will allow entry into the 
Status Mode screens. If you decide not to enter the Status 
Mode, press the MENU key and you will return to the 
normal operation screen. 
 
  Press the DOWN arrow key and the following screen 
appears: 
 
 

- ALARMS TRIPPED - 

IN  LO  HI  CHT  INT  EE 

 
 
  The Alarms Tripped screen will display any conditions 
that have occurred. 
 
  To clear the alarms press the DOWN arrow key. 
Should an alarm still be tripped, it will still be shown on 
the display. 
 
  The definition of the alarms are as follows: 
 
  IN  =  There is no 4-20 mA signal or the input current 
is below the pen arm zero current value. 
 
  LO  =  This indicates that the low alarm set point has 
been tripped. This set point may be changed, refer to the 
Calibration Section of this manual. 
 
  HI  =  This indicates that the high alarm set point has 
been tripped. This set point may be changed, refer to the 
Calibration Section of this manual. 
 
  CHT  =  This indicates that the chart has made a 
complete rotation and the chart needs to be changed. 
 
  INT  =  Indicates a contact integrator pulse output has 
occurred. 
 
  EE  =  EEPROM read/write error which indicates a 
failure in the microprocessor. Consult the factory. 
 
 
 
 
 

 
 
 
  To return to the normal operating screen press the 
MENU key. 
 
  To enter the Self Test screen press the ENTER key and 
the following screen will appear: 
 
 

- SELF TEST - 

PRESS UP TO ACTIVATE 

 
 
  If you decide not to enter into the Self Test section, 
press the MENU key and you will return to the normal 
display screen. 
 
  To enter into the Self Test section press the UP arrow 
key and the following screen will appear: 
 
 

- SELF TEST - 

EEPROM TEST=> PASSED 

 
 
 
  This tests the EEPROM and indicates if it passed or 
failed. This takes a few seconds and then the following 
screen will appear: 
 
 

- SELF TEST - 

VREF TEST=> PASSED 

 
 
  This tests the reference voltage and indicates if it 
passed or failed. The following screen will appear: 
 
 

- SELF TEST - 

SERVO TEST=> PASSED 

 
 
 
  This tests the servo drive system and indicates if it 
passed or failed. 
 
  Should any of the screens indicate a failure, contact the 
factory for the appropriate action to be taken. 
 
  Upon completion of the Self Test the unit will return to 
the normal operating display screen. This completes the 
Status Mode Section. 

8

 

Содержание 3000+























Отзывы: