background image

 

-TOTALIZER WORD- 

0

15

 

000  0000  0000 

 
  The Totalizer Word is required to setup the time base to 
properly totalizer in the selected option units. The 
totalizer word is defined as follows: 
 

 

HEX

  

  

2,000,000

  x  

ec

in Units/S

 

Flow

 

Max.

Multiplier

Totalizer 

=

 

 
EXAMPLE: 
Maximum flow  =  1800  x  1 BPM (Barrels/min) 
Totalizer multiplier  =  BAR  x  100 
Totalizer Word  = 
[100/(1800/60)] x 2,000,000  =  6666666.6 
 

Converted to Hexadecimal  =  65B9AA (see the Decimal 
to Hexadecimal Conversion Section). 
 
The TOTALIZER WORD is 0000 0065 B9AA 

 
NOTE: The totalizer word must be greater than Hex 
1000. 

 
  Use the UP and DOWN arrow keys to change each 
digit to the required value and the RIGHT arrow to move 
the cursor. The ENTER key must be depressed after each 
set of four digits. Return to Page 10 where the next screen 
will be the Chart Speed selection. 
 
 
 

 
 
 
 
 
 
 

ERROR SCREENS 

 
  There are several Error Screens that will be displayed 
by the recorder if the microprocessor detects errors in the 
values programmed into the recorder. 
 

 

-CHART PEN ZERO- 

<INPUT ZERO ERROR> 

 
 

OR 

 
 

-CHART PEN SPAN- 

<INPUT SPAN ERROR> 

 
 
  If either of the two above Error Screens appear during 
the chart pen adjusting procedure, one of the following 
problems probably occurred: 
 
  1.  There was not a 4-20 mADC analog signal to the 
recorder analog channel you selected while adjusting the 
chart zero span. 
 
  2.  An analog input signal channel was selected 
without adjusting the chart pen zero and span of this 
channel. 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
  3.  The Zero and Span of the recorder have been 
adjusted too close to the same input value. 
 
  To correct these errors, readjust the Chart Pen Zero and 
Span while inputting the 4-20 mADC analog signal to the 
proper selected recorder channel. Refer to the Calibration 
Mode Section of this manual. 
 

 

-STORING PARAMETERS- 

<TOTALIZER WORD ERROR> 

 
 
  If the above Error Screen appears after pressing the 
ENTER key to store the calibration adjustments, this 
indicates that you have selected a totalizer multiplier that 
is too low for your selected flow rate. To correct this 
error, re-enter the Calibration Mode and when the 
Totalizer Multiplier Screen appears, increase the totalizer 
multiplier and press the ENTER key. Then press the 
MENU key to store the new multiplier and return to the 
normal operating screen. 
 
  If you still have a Totalizer Word Error message in the 
Storing Parameters screen, repeat the above procedure 
until the error is not present. 
 

Содержание 3000+























Отзывы: