Baby Lock Ellure PLUS BLR3 страница 44 Скачать руководство пользователя

Страница: 44 / 200

GETTING READY

Replacing the Presser Foot

This section describes how to replace the presser foot.

Presser foot precautions

Be sure to observe the following precautions concerning the presser feet.

CAUTION

Replacing the presser foot

Replace the presser foot as described below.

Press

(“Needle Position” button) once or

twice to raise the needle.

“Needle Position” button

Turn off the sewing machine.

CAUTION

Raise the presser foot lever.

Presser foot lever

The presser foot is raised.

Press the black button at the back of the
presser foot holder.

Black button

Presser foot holder

The presser foot holder releases the presser
foot.

●

Use the presser foot appropriate for the type of stitch that you wish to sew, otherwise the
needle may hit the presser foot, causing the needle to bend or break.

●

Only use presser feet designed specifically for this sewing machine. Use of any other presser
foot may result in injuries or damage to the machine.

●

Before replacing the presser foot, be sure
to turn off the sewing machine, otherwise
injuries may occur if

(“Start/Stop”

button) is accidentally pressed and the
machine starts sewing.

Содержание Ellure PLUS BLR3









































































































































































































Результаты поиска

Содержание Ellure PLUS BLR3

Отзывы:

Похожие инструкции для Ellure PLUS BLR3

Бренды по названию

Популярные бренды

Baby Lock Ellure PLUS BLR3, Инструкция и справочник

Результаты поиска

Содержание Ellure PLUS BLR3

Отзывы:

Похожие инструкции для Ellure PLUS BLR3

Бренды по названию

Популярные бренды