Baby Lock Ellure PLUS BLR3 страница 19 Скачать руководство пользователя | Manualshive

Страница: 19 / 200

background image

Turning the Machine On/Off

17

1

Turning on the machine

Prepare the included power cord.

Make sure that the sewing machine is turned
off (the main power switch is set to “

”), and

then plug the power cord into the power
supply jack on the right side of the machine.

Insert the plug of the power cord into a
household electrical outlet.

a

Power supply jack

Press the right side of the main power switch
on the right side of the machine to turn the
machine on (set it to “I”).

X

The light, LCD and

/

(“Start/Stop”

button) light up when the machine is turned
on.

Turning off the machine

When you are finished using the sewing machine,
turn it off. In addition, before transporting the sewing
machine to another location, be sure to turn it off.

Make sure that the machine is not sewing.

Press the left side of the main power switch on
the right side of the machine to turn the
machine off (set it to “

”).

X

The sewing lamps and the LCD go off when
the machine is turned off.

Unplug the power cord from the electrical
outlet.

Grasp the plug when unplugging the power
cord.

Unplug the power cord from the power supply
jack.

Note

z

If a power outage occurs while the sewing
machine is being operated, turn off the
sewing machine and unplug the power cord.
When restarting the sewing machine, follow
the necessary procedure to correctly operate
the machine.

(For U.S.A. only)

z

This appliance has a polarized plug (one
blade wider than the other). To reduce the
risk of electrical shock, this plug is intended
to fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact
a qualified electrician to install the proper
outlet. Do not modify the plug in any way.

«
...
17
18
19
20
21
...
»

Содержание Ellure PLUS BLR3









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ellure PLUS BLR3

Бренд: Janome Страницы: 63

Бренд: Alfa Network Страницы: 55

Бренд: Sailrite Страницы: 38

Lavina 25L HV Pro

Бренд: Superabrasive Страницы: 29

Бренд: U.S. Products Страницы: 10

Бренд: Thomas Страницы: 24

Бренд: Parish Страницы: 12

Бренд: Pfaff Страницы: 90

Бренд: UCHIDA Страницы: 60

Бренд: hobbylock Страницы: 32

Pro-Stitcher BLPS3

Бренд: Baby Lock Страницы: 105

Бренд: Truvox Страницы: 16

Бренд: JUKI Страницы: 32

Бренд: Baby Lock Страницы: 33

Бренд: Brother Страницы: 16

Бренд: Brother Страницы: 60

Бренд: Brother Страницы: 19

Entrepreneur Pro PR1050X

Бренд: Brother Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды