Baby Lock Ellure PLUS BLR3 страница 194 Скачать руководство пользователя | Manualshive

Страница: 194 / 200

background image

192

APPENDIX

Upgrading Your Machine’s Software Using USB Media

You can use USB media and a computer to download software upgrades for your sewing machine.
When an upgrade program is available on our website at “www.babylock.com”, please download the
file(s) following the instructions on the website and steps listed below.

Note

z

When using USB media to upgrade the software, check that no data other than the upgrade file is saved
on the USB media being used before starting to upgrade.

z

Upgrade file can be recalled from a USB flash drive (USB flash memory) of any size.

z

USB media should be reformatted before starting the upgrade process.

Memo

z

When the machine's software is upgraded, saved combinations of character and decorative stitches are
erased. However, saved embroidery patterns are not erased.

Press and hold the

/

(Settings key)

while turning on the machine.

X

The following screen appears.

Insert the USB media into the USB port on the
machine. The media device should only
contain the upgrade file.

a

USB port for media

b

USB media

Note

z

When using USB media equipped with an access
indicator, the access indicator will begin flashing
after the media is inserted into your computer or
machine, and may take about 5 to 6 seconds
before the media is recognized. (The length of
time differs depending on the USB media.)

Press .

X

The following screen appears.

Note

z

If an error occurred, a text error message will
appear. At this time, turn the machine off, and
then start the procedure again from step

.

When the following screen appears, upgrading
is completed.

Remove the USB media, and turn the machine
off and on again.

«
...
192
193
194
195
196
...
»

Содержание Ellure PLUS BLR3









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ellure PLUS BLR3

Бренд: Panasonic Страницы: 2

Бренд: Gamma Страницы: 11

DREAMSTITCHER 600SO

Бренд: Reliable Страницы: 32

Бренд: Pfaff Страницы: 130

Бренд: Tennant Страницы: 155

Бренд: Panasonic Страницы: 7

Бренд: Panasonic Страницы: 11

Бренд: Panasonic Страницы: 16

Бренд: Panasonic Страницы: 16

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 26

Бренд: Panasonic Страницы: 88

Бренд: Panasonic Страницы: 101

Бренд: Panasonic Страницы: 103

Бренд: Panasonic Страницы: 105

Бренд: Panasonic Страницы: 109

Бренд: Panasonic Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды