Baby Lock Ellure PLUS BLR3 страница 110 Скачать руководство пользователя

Страница: 110 / 200

108

UTILITY STITCHES

■

Using the optional quilting guide

Use the quilting guide to sew parallel stitches that
are equally spaced.

Insert the stem of the quilting guide into the
hole at the rear of the walking foot or presser
foot holder.

Walking foot

Presser foot holder

Adjust the stem of the quilting guide so that
the guide aligns with the seam that has already
been sewn.

Note

The optional quilting guide is available
through Baby Lock retailers.

Free-motion quilting

With free-motion quilting, lower the feed dogs (using
the drop feed lever) so that the fabric can be moved
freely in any direction.
When free-motion quilting, use the following
instructions with the optional quilting foot.

Remove the presser foot and the presser foot
holder.

• Refer to “Removing and attaching the presser

foot holder” (page 44).

Secure the quilting foot with the presser foot
holder screw.

The pin on the quilting foot should be
positioned over the needle clamp screw.

Pin on quilting foot

Presser foot holder screw

Needle clamp screw

Hold the quilting foot in place with your right
hand, and then tighten the presser foot holder
screw using the screwdriver in your left hand.

Presser foot holder screw

Содержание Ellure PLUS BLR3









































































































































































































Результаты поиска

Содержание Ellure PLUS BLR3

Отзывы:

Похожие инструкции для Ellure PLUS BLR3

Бренды по названию

Популярные бренды

Baby Lock Ellure PLUS BLR3, Инструкция и справочник

Результаты поиска

Содержание Ellure PLUS BLR3

Отзывы:

Похожие инструкции для Ellure PLUS BLR3

Бренды по названию

Популярные бренды