Baby Lock Ellure PLUS BLR3 Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 200

Baby Lock Ellure PLUS BLR3 Скачать руководство пользователя страница 101

Zipper/Piping Insertion

99

3

Zipper/Piping Insertion

A zipper and piping can be sewn in place.

There are many methods for inserting zippers and pipings. The procedures for inserting a centered zipper
and a piping are described below, with the adjustable zipper/piping foot.

Inserting a centered zipper

Refer to step

–

of “Inserting a centered

zipper” (page 94).

Remove the presser foot and presser foot
holder (page 44) to attach the screw-on
adjustable zipper/piping foot.

Note

z

Use a screw driver to securely tighten the
screw that holds the presser foot. If the screw
is loose, the needle may break and cause
injures.

Select stitch

1

.

Loosen the positioning screw on the back of
the presser foot.

a

Positioning screw

Slide the presser foot over either the left or
right feed dog.

Change the needle position so that the needle
does not touch the presser foot.

For details, refer to “Adjusting the stitch width”
(page 56).

a

Needle drop point

Stitch Name

Pattern

Application

Stitch Width

[mm (inch)]

Stitch Length

[mm (inch)]

Presser

Foot

Auto

Manual

Auto

Manual

Straight stitch

(left needle

position)

1

Attaching zippers Sewing
concealed seams and piping

0.0

(0)

0.0–7.0

(0–1/4)

2.5

(3/32)

0.2–5.0

(1/64–3/16)

1

Left sewing position

Right sewing position

1

«
...
99
100
101
102
103
...
»

Содержание Ellure PLUS BLR3









































































































































































































Отзывы:

Нет отзывов