Baby Lock Ellure PLUS BLR3 Скачать руководство пользователя | Manualshive

Страница: 189 / 200

background image

Troubleshooting

187

5

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

Error messages

When erroneous operations are performed messages and advice on operation will be displayed on the LCD.
Follow what is displayed. The message may disappear if the operation is performed correctly. The message will
disappear if

is pressed while the message is displayed.

Error Message

Probable Cause

There is a possibility that the data for the selected pattern is corrupted.

Either the “Start/Stop” button or the “Reverse/Reinforcement Stitch”
button was pressed at a screen other than the sewing screen.

The “Start/Stop” button was pressed without connecting the foot
controller while the setting for adjusting the stitch width using the
sewing speed controller is set to “ON”.
You have selected a pattern for which width control cannot be used.

The twin needle setting is selected while a pattern that cannot be sewn
with the twin needle is selected.
Press

to cancel the twin needle setting. If the twin needle is

installed, replace it with a single needle. Then, select the pattern again.
Press

to return to the previous screen.

Upper thread broken.
Upper thread not set up correctly.
Upper thread has run out.

CAUTION
Be sure to rethread the machine. If you press the “Start/Stop” button
without rethreading the machine, the thread tension may be wrong or
the needle may break and cause injury.

The machine is deleting a previously saved pattern while in embroidery
edit mode.

The “Start/Stop” button was pressed while the foot controller was
connected.
You tried to use the foot controller for embroidery.

You attempted to select a pattern after the USB media containing the
pattern has been disconnected, then reconnected.

on the LCD was pressed when no card was inserted.

A stitch other than the buttonhole, bar tack or darning stitch was
selected and the “Start/Stop” button was pressed while the buttonhole
lever is lowered.

You recalled a pattern while no USB media is connected.

«
...
187
188
189
190
191
...
»

Содержание Ellure PLUS BLR3









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ellure PLUS BLR3

Бренд: DFG Страницы: 5

Coronet BLCT16A

Бренд: Baby Lock Страницы: 62

Бренд: Kärcher Страницы: 237

Бренд: Ricoh Страницы: 147

Бренд: Janome Страницы: 63

GBC WireBind W18

Бренд: GBC Страницы: 38

Бренд: National Instruments Страницы: 18

3001 Silent Drive

Бренд: ProForm Страницы: 16

Бренд: Racing Страницы: 3

Thermal Binding Machine 8.2

Бренд: Peleman Страницы: 2

Бренд: Royal Sovereign Страницы: 36

Бренд: Bernina Страницы: 54

Бренд: Bernina Страницы: 140

Бренд: Horizon Fitness Страницы: 50

Бренд: Yamata Страницы: 51

Бренд: Ice Страницы: 43

Бренд: LOBSTER Страницы: 8

ZJ-M3-S500-SF-LK2-V2

Бренд: ZOJE Страницы: 190

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды