Baby Lock Ellure PLUS BLR3 страница 153 Скачать руководство пользователя

Страница: 153 / 200

Attaching the Embroidery Frame

151

Attaching the Embroidery Frame

This section describes how to attach the embroidery frame.

Attaching the embroidery
frame

Wind the embroidery bobbin thread onto the
bobbin and set it into the bobbin case.

• For details, refer to “Winding/Installing the

Bobbin” (page 23).

Raise the presser foot lever.

Presser foot lever

Pass the embroidery frame under the presser
foot while raising the presser foot lever even
further.

CAUTION

While lightly holding the lever on the frame
holder to the left, align the two pins on the
embroidery frame holder with the mounting
brackets on the frame, and then press the
frame into the embroidery frame holder until a
click is heard.

After pressing the front mounting bracket onto
the pin so that it clicks into place, press the
back mounting bracket into place.

Lever

Mounting brackets

Pins

Note

Be sure to insert both pins. If only the
forward or the back pin is inserted, the
pattern may not turn out correctly.

CAUTION

●

Do not hit the needle with your finger or
the embroidery frame. It may cause injury
or needle breakage.

●

Correctly set the embroidery frame into
the embroidery frame holder. Otherwise,
the presser foot may hit the embroidery
frame, resulting in injury.

Содержание Ellure PLUS BLR3









































































































































































































Результаты поиска

Содержание Ellure PLUS BLR3

Отзывы:

Похожие инструкции для Ellure PLUS BLR3

Бренды по названию

Популярные бренды

Baby Lock Ellure PLUS BLR3, Инструкция и справочник

Результаты поиска

Содержание Ellure PLUS BLR3

Отзывы:

Похожие инструкции для Ellure PLUS BLR3

Бренды по названию

Популярные бренды