background image

Conventions Used in This Manual

i

To prevent injury to the operator and others, and to prevent property damage, the following types of safety

precautions are indicated:

In describing the product, this manual uses the icons and conventions listed below. 

Use caution when handling the product.

The indicated action is prohibited.

Be sure to follow the indicated instructions.

Handling Precautions

:

Handling Precautions indicate items that the user should pay attention to when

handling the MCF.

Note

:

Notes indicate information that might benefit the user.

:

This indicates the item or page that the user is requested to refer to.

(1), (2), (3):

Numbers within parentheses indicate steps in a sequence or parts of an

explanation.

>>:

Indicates the result of an operation, details displayed on the personal computer or

other devices, or the state of the device after operation.

WARNING

Warnings are indicated when mishandling this product might result in

death or serious injury.

CAUTION

Cautions are indicated when mishandling this product might result in

minor injury to the user, or only physical damage to the product.

Содержание MCF Series



























































Отзывы: