background image

AB-7050 

17 

Precautions for wiring 

IMPORTANT: 

  Do not connect the lead wires for temperature output to the power supply line to prevent smoking or burnout. 

Make sure all the wires are correctly connected before supplying power. 

  Single Neosensor must be powered by a single 24 V AC transformer.  Do not connect the transformer to any 

other device in addition to Neosensor. 

 

  For power supply wiring and temperature/humidity output wiring, 1.25 mm

2

 or greater shielded multi-core cables (JIS 

CVV-S) are recommended.  1.25 mm

2

 or greater JIS IV cable is also connectable.  Be sure to ground the shielding on the 

controller side.   
The maximum cable length is 100 m. 

  Because the temperature sensor model with RTD (Pt1000) output is two-wire, the wire resistance will cause measuring 

error.  For instance, 1.25 mm

2

 size wire causes approx. 0.1 °C measuring error every 10 m.  Correct the measuring error by 

setting the controller in connection. 

 
Transformer for Neosensor (humidity sensor, temperature/humidity sensor models) 

IMPORTANT: 
 

Use isolated transformer to supply 24 V AC power.   
Single Neosensor must be powered by a single 24 V AC transformer.  If the multiple Neosensor or a 
Neosensor and a device in connection are powered by a single 24 V AC transformer, the common wiring will 
form a loop, and Neosensor will get damaged. 

 

24 V AC transformer: Two Neosensor powered by a single transformer 

 

 

 

 

 

 

 

 

 

 

Figure 22. Bad wiring examples: Two Neosensor (temperature/humidity sensors) powered by a single 24 V AC transformer 

 

24 V AC transformer: Two Neosensor separately powered by two transformers 

 

 

 

 

 

 

 

 

 

 

Figure 23.  Good wiring example: Two Neosensor (temperature/humidity sensors) powered by separate 24 V AC transformers 

 

If the transformer is misconnected, it will short-circuit through the common wiring.

Bad wiring 

Controller 

Common 
wiring 

24 V AC 

Temperature/ 

humidity sensor 

 

 

 

 

Temperature/ 

humidity sensor 

Bad wiring 

Common wiring forms a loop. 

24 V AC

Temperature/ 

humidity sensor 

Temperature/ 

humidity sensor 

Controller

Common 
wiring 

Common wiring does not form a loop.

Good wiring 

24 V AC

Temperature/ 

humidity sensor 

Controller

24 V AC

Temperature/ 

humidity sensor 

Содержание HTY7043T1P00





















Отзывы: