background image

AXELL D-CSR 3302 US VHF REPEATER

 

PRODUCT DESCRIPTION AND US

ER’S MANUAL 

© Axell Wireless Ltd 

DOC PN 0034B-UM REV. 2.1 

III 

This Product Manual provides the following information: 

  Description of the Repeater  

  Procedures for setup, configuration and checking the proper operation of the Repeater  

  Maintenance and troubleshooting procedures  

This Product Manual is intended for experienced technicians and engineers. It is assumed 
that  the  customers  installing,  operating,  and  maintaining  Axell  Wireless  Repeaters  are 
familiar with the basic functionality of Repeaters. 

Confidential - Authorized Customer Use 
This  document  may  be  used  in  its  complete  form  only  and  is  solely  for  the  use  of  Axell 
Wireless  employees  and  authorized  Axell  Wireless  channels  or  customers.  The  material 
herein is proprietary to Axell Wireless. Any unauthorized reproduction, use or disclosure of 
any part thereof is strictly prohibited. 
All trademarks and registered trademarks are the property of their respective owners. 

Contents herein are current as of the date of publication. Axell Wireless reserves the right to 
change the contents without prior notice. The information furnished by Axell Wireless in this 
document  is  believed  to  be  accurate  and  reliable.  However,  Axell  Wireless  assumes  no 
responsibility for its use. In no event shall Axell Wireless be liable for any damage resulting 
from loss of data, loss of use, or loss of profits and Axell Wireless further disclaims any and 
all  liability  for  indirect,  incidental,  special,  consequential  or  other  similes  damages.  This 
disclaimer  of  liability  applies  to  all  products,  publications  and services  during  and  after  the 
warranty period. 

Safety to Personnel 

  Before installing or replacing any of the equipment, the entire manual should be read 

and understood.  

 

This equipment is to be installed only in a restricted access location. 

  Throughout this manual, there are "Caution" warnings. "Caution" calls attention to a 

procedure or practice, which, if ignored, may result in injury or damage to the system, 
system component or even the user. Do not perform any procedure preceded by a 
"Caution" until the described conditions are fully understood and met. 

 

CAUTION!

 

This  notice  calls  attention  to  a  procedure  or  practice 

that,  if  ignored,  may  result  in  personal  injury  or  in  damage  to  the 
system  or  system  component.  Do  not  perform  any  procedure 
preceded  by  a  "Caution"  until  described  conditions  are  fully 
understood and met. 

 

 

Содержание D-CSR 3302


































































Отзывы: