background image

AXELL D-CSR 3302 US VHF REPEATER

 

PRODUCT DESCRIPTION AND US

ER’S MANUAL 

VIII 

DOC PN 0034B-UM REV. 2.1 

© Axell Wireless Ltd 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

Caution: Safety to 

personnel.

 

Before installing or replacing any of the equipment, the entire manual 
should be read and understood. 

The  user  needs  to  supply  the  appropriate  AC  or  DC  power  to  the 
repeater. Incorrect power settings can damage the repeater and may 
cause injury to the user. 

Please  be  aware  that  the  equipment  may,  during  certain  conditions 
become  very  warm  and  can  cause  minor  injuries  if  handled  without 
any protection, such as gloves

 

 

 

Caution: Safety to 

equipment

 

When  installing,  replacing  or  using  this  product,  observe  all  safety 
precautions during handling and operation. Failure to comply with the 
following  general  safety  precautions  and  with  specific  precautions 
described  elsewhere  in  this  manual  violates  the  safety  standards  of 
the design, manufacture, and intended use of this product. 

 

Axell  Wireless  assumes  no  liability  for  the  customer's  failure  to 
comply  with  these  precautions.  This  entire  manual  should  be  read 
and understood before operating or maintaining the repeater. 

 

Warning: Restricted 

Access Location 

Access to the Axell unit installation location is restricted to SERVICE 
PERSONNEL  and  to  USERS  who  have  been  instructed  on  the 
restrictions and the required precautions to be taken. 

 

 

Attention: Electrostatic 

Sensitivity 

 

Observe electrostatic precautionary procedures. 

ESD = Electrostatic Discharge Sensitive Device.  

Semiconductor  transmitters  and  receivers  provide  highly  reliable 
performance when operated in conformity with their intended design. 
However,  a  semiconductor  may  be  damaged  by  an  electrostatic 
discharge inadvertently imposed by careless handling. 

Static electricity can be conducted to the semiconductor chip from the 
centre  pin  of  the  RF  input  connector,  and  through  the  AC  connector 
pins.  When  unpacking  and  otherwise  handling  the  repeater,  follow 
ESD  precautionary  procedures  including  use  of  grounded  wrist 
straps, grounded workbench surfaces, and grounded floor mats. 

 

Caution: Battery 

Replacement 

Risk of explosion if battery is replaced with incorrect type. Dispose of 
used batteries according to instructions. 

Содержание D-CSR 3302


































































Отзывы: