AXELL D-CSR 3302 страница 12 Скачать руководство пользователя

Страница: 12 / 65

AXELL D-CSR 3302 US VHF REPEATER

PRODUCT DESCRIPTION AND US

ER’S MANUAL

Doc PN 0034B-UM Rev. 2.1

1.3

Interfaces

The repeater contains interfaces both externally and internally (accessed by opening the
door):



External interfaces - RF, modem antenna (where relevant) and power connections are

located externally. (Optional external Ethernet connection may be provided).



Internal interfaces - management connections (ETH, SIM

–for systems with GPRS

modem), power switches and backup battery

1.3.1 External Interfaces

The repeater is secured with two locks located on the repeater door. The repeater interfaces
are located on both the left and right side panels as follows:



Left panel

– Base/Donor antenna port



Right panel

– Mobile/Service antenna port as well as power, GND, and alarm

connections

NOTE: Depending on your installation, modem antenna and Ethernet ports may also be located on

either the left or right panel.

Figure 1-2. D-CSR Door Locks and Left Side Panel Interfaces

Figure 1-3. D-CSR right side panel interfaces

Содержание D-CSR 3302


































































Результаты поиска

Содержание D-CSR 3302

Отзывы:

Похожие инструкции для D-CSR 3302

Бренды по названию

Популярные бренды

AXELL D-CSR 3302, Руководство пользователя

Результаты поиска

Содержание D-CSR 3302

Отзывы:

Похожие инструкции для D-CSR 3302

Бренды по названию

Популярные бренды