AXELL D-CSR 3302 страница 28 Скачать руководство пользователя

Страница: 28 / 65

AXELL D-CSR 3302 US VHF REPEATER

PRODUCT DESCRIPTION AND US

ER’S MANUAL

Doc PN 0034B-UM Rev. 2.1

4.9

Antenna (RF) Connections

4.9.1 Verifying the Link between the BTS and the Repeater

This test checks the signal strength from the BTS antenna to the Repeater.

Proceed as follows:

1. Using a Spectrum analyzer, measure the received signal from BTS at the Donor

antenna port near the Repeater.

2. Adjust the Donor antenna direction to receive the maximum signal strength.

3. Compare the received signal strength with the calculated signal strength from the design

phase.

In case of discrepancy, check for one of the following:



Antenna out of direction



Antenna tuned to side lobe instead of main lobe



Antenna connector or antenna cable faulty



Line-of-sight problem (obstruction), etc.



4.9.2 RF Antenna Connections

Refer to the following figure for the D-CSR RF antenna connections.

NOTE: For models supporting a GPRS modem, you may also connect the modem antennas

at this stage. If your repeater includes a modem, the modem antenna port may either be on
the left or right panel

– depending on your enclosure.

Figure 4-11. Donor Antenna Connection

Содержание D-CSR 3302


































































Результаты поиска

Содержание D-CSR 3302

Отзывы:

Похожие инструкции для D-CSR 3302

Бренды по названию

Популярные бренды

AXELL D-CSR 3302, Руководство пользователя

Результаты поиска

Содержание D-CSR 3302

Отзывы:

Похожие инструкции для D-CSR 3302

Бренды по названию

Популярные бренды