DETAIL OF HYBRID REMOTER FOR MACROTEL X1
| DETAIL OF HYBRID REMOTER FOR MACROTEL X1
37
Echo Tail:
this is the value in ms of the Echo which is eliminated by the
DSP of Macrotel X1 and Macrotel X2. It is combined with the
Echo
Cancelling
control that adjusts the echo cancelling speed on the telephone
line. This parameter acts on an automatic variation filter to cancel the echo.
The operating parameters self-adapt to the status of the line, of the input
and output levels. The variable parameters are the maximum recoverable
echo delay (16ms or 32ms) and the intervention modes (OFF, FAST,
NORMAL, SLOW)
Hook Mode:
this is the Telephone hybrid answering mode, which can
range from
Manual
, i.e. Off-Hook (answer) only when a call is answered
manually, to
Auto Off-Hook after n rings
, i.e. the automatic answering of
the Telephone Hybrid after n rings. The number of rings available is: 1
– 2 –
3
– 4 – 5.
Drop Mode
: this is used to hook (
Drop
) or automatically end a call when
the CPTS or closing signal is recognised. The value of the CPTD signal can
be set in the Program Settings section
under “CPTD Characteristics”, after
having set the “Country Line Setup”
Line Sensitivity:
this is used to adjust the input gain from the telephone line from -6dB ÷ +6dB.
Line Input Filter:
this is a high-pass filter (HPf) placed on the telephone line in order to adapt and improve as much as
possible the incoming audio of one’s phone. Range of allowed values: from 100 Hz to 350 Hz with 50Hz/steps
Line Output Filter:
this is a low-pass filter (LPf) placed on the telephone line in order to adapt and improve as much as
possible the incoming audio of one’s phone. Range of allowed values: from 2.6 kHz to 5.0 kHz
Line Type:
this command is used to select the telephone line to connect to the Telephone Hybrid. The Macrotel X1 can
be connected to one 2Wire POTS / PSTN line with RJ11 plug (two-wire) or to one Wireless line through the connection
of an external
GSM
module(opt.) This command is used to select which line to use,
2Wire
or
GSM
. The
2Wire
line and
the Wireless
GSM
line cannot be used at the same time on the same Telephone Hybrid. Macrotel X2 features two POTS
/ PSTN and External GSM lines.
Accept External Commands:
by flagging this checkbox Macrotel X1 an Macrotel X2 are enabled to accept or not
accept commands received on the GP In and GP Out (SubD 15p HD) ports.
AGC, EQ, Atten:
Section made up of three parameters: AGC,
Equaliser and Attenuation.
AGC & AGC Speed:
this is the maximum gain value of the Automatic
gain Control (AGC). The parameters that can be set are the maximum
gain (from +1dB to +12dB) and the variation speed (from OFF (0dB/s)
to 2dB/s, in 0.1 steps), i.e. by how many dB per second the signal level
is increased (gain).
High Eq & Bass Eq:
these two parameters act directly on the two-band equaliser inside the Macrotel X audio
processor. The gain that can be set ranges from +0.0dB to a maximum of +8.0dB. The equaliser frequencies are set at
300Hz Bass Eq and 2kHz High Eq.
Attenuation
: In this section the attenuation values can be adjusted from 1dB a 30dB. Attenuation can be enabled or the
interlocutor can be placed on “
HOLD
”, which takes attenuation to-∞. See the
Special notes concerning
Ducking/Conference between Hybrids
to disable this parameter when the device is used in certain configurations.
UNDO:
press UNDO to reset the values set in the whole Hybrid 1 and Outputs section
to the values set on the device before the opening of the control panel.
