manualshive.com logo in svg

Axcess NT132, Руководство по установке, Страница: 97 / 110

Поделиться
Скачать
Axcess NT132 Скачать руководство пользователя страница 97

Troubleshooting the System

© 1999, AXCESS

TM

 Inc.

750.001.003

Revised June 1999

97

Step 8: 

Check the 10-wire header within the Toggle Switch ATU to
be sure that it is seated properly. See page 74 for a
discussion of seating the header.

Step 9: 

Check the LEDs within the Reader to be sure they are on.

Step 10: 

Check the Reader to see if it is connected to a power
source. Information on providing power can be found on
page 32.

Step 11: 

Check to see if the 30-turn pot adjustment switch is turned
to the maximum on the TX card in the Reader. See the
chapter 

Modifying Antenna Range: Adjusting the

Transmitter Card

, page 77.

Step 12: 

Check for any environmental interference affecting the
system performance.

Swing Frame Antenna

Problem: The Swing Frame Antenna has diminished or no range

Step 1: 

Ensure that RG-58/U with 100% foil shield coverage is
used.

Step 2: 

Ensure that the cable lengths are within specifications: no
more than 80 feet between the Reader and the ATU and
no more than 20 feet between the ATU and the antennas.

Step 3: 

Ensure that the connectors are well fastened and in good
order.

Step 4: 

Ensure that TX is connected to TX and RX is connected to
RX on the Reader, ATU and antennas.

Step 5: 

Ensure that the Swing Frame Antenna has been
positioned correctly. The Swing Frame Antenna is for
indoor use only.

Step 6: 

Ensure that the ATU is tuned. See page 73 for information.

Step 7: 

Ensure that the 10-wire connector is well seated in the
Toggle Switch ATU. See page 74 for a discussion of
seating the header.

Step 8: 

Check for continuity on the connectors, cable and transmit
antenna. The transmit antenna should have continuity.
See page 87 for details on checking continuity.

Step 9: 

Check the LEDs within the Reader to be sure they are on.

Step 10: 

Check the Reader to see if it is connected to a power
source. Information on providing power can be found on
page 32.

Step 11: 

Check to see if the 30-turn pot adjustment switch is turned
to the maximum on the TX card. See the chapter

Содержание NT132















































































































Отзывы:

Нет отзывов