Axcess NT132 Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 110

Axcess NT132 Скачать руководство пользователя страница 72

Swing Frame Antenna System Installation

72

750.001.003

Revised June 1999

© 1999 AXCESS

TM

Inc.

Step 2:

Attach BNC connectors to both ends of each cable.

Step 3:

Attach the RX connector on the back of the Swing Frame
Antenna with the

RX Antenna

connector on the ATU.

Step 4:

Attach the TX connector on the back of the Swing Frame
Antenna with the

TX Antenna

connector on the ATU.

Step 5:

Position the antenna in its approximate final location – but
do not permanently install it at this time. Have a helper
hold the antenna in various positions until maximum
coverage is achieved.

Step 6:

Test the system by positioning the LED Test Tag at
strategic points to ensure complete coverage. It will light
up and flash when it is within the field.

Step 7:

Apply power to the Reader. See the

Connecting Power to

the Reader – All Types

section, page 32.

Step 8:

Tune the ATU. See the section

Maximizing Antenna

Performance with the ATU

, page 73.

Step 9:

Permanently mount the Swing Frame on the wall using the
mounting holes at the bottom and top of the frame and
dress/tie-wrap all cabling.

«
...
70
71
72
73
74
...
»

Содержание NT132















































































































Отзывы:

Нет отзывов