Axcess NT132 Скачать руководство пользователя страница 32

Страница: 32 / 110

Reader Installation

750.001.003

Revised June 1999

Inc.

Connecting Power to the Reader – All Types

IMPORTANT!

Finish installing the Reader before applying power.

All Readers come with a 24V, 700 mA wall adapter that plugs into a
110 outlet. If uninterruptible power is an issue, a UPS can be used.

Wires to
Reader

Wires from
AC adapter

24V

Figure 13 Power terminals for the Reader

Grounding the Reader

The Reader needs to be properly grounded. Failure to ground the
Reader will result in erratic performance.

Step 1:

Run 14 AWG wire from a solid earth ground to the ground
lug on the outside of the Reader case (Figure 6).

Step 2:

If the Reader is connected to a Wiegand control panel,
ensure that the Wiegand control panel is similarly
grounded.

AC Adapter

The AC adapter wires (Figure 14) are labeled as follows:

80 C VW - 1 22 AWG X 2C

Power

Ground

Figure 14 AC adapter wires

Power

is marked with the dashed white line.

Ground

is black and has the gauge information printed on it.

Содержание NT132















































































































Результаты поиска

Содержание NT132

Отзывы:

Axcess NT132, Руководство по установке, Страница: 32 / 110

Результаты поиска

Содержание NT132

Отзывы: