Axcess NT132 Скачать руководство пользователя страница 9

Страница: 9 / 110

General Installation Information

Inc.

750.001.003

Revised June 1999

Things to Consider

IMPORTANT!

The Reader must be installed in a moisture-free

environment at approximately room temperature and a minimum of
36 inches above the floor. Installation at eye height is recommended.

If possible, position the Reader and the ATU where they are not
readily accessible to help prevent tampering or accidental damage.

Cabling

•

Use only RG-58/U coaxial cable with 50-ohm impedance
(nominal), solid copper center conductor, 55% tinned copper
braid or better, 100% foil shield coverage (for example, Belden
9310).

•

The maximum recommended cable length between the Reader
and ATU is 80 feet.

•

The maximum recommended cable length between the ATU and
the antennas is 20 feet.

Reader

ATU

Bar Antenna

20 feet

80 feet

Figure 2 Maximum recommended cable lengths

IMPORTANT!

System performance may be adversely affected if a

different cable is used, the cable lengths exceed recommendations,
or if the cable is kinked.

NOTE: All distances are by cable run unless specified otherwise.

Содержание NT132















































































































Результаты поиска

Содержание NT132

Отзывы:

Axcess NT132, Руководство по установке, Страница: 9 / 110

Результаты поиска

Содержание NT132

Отзывы: