Axcess NT132 Скачать руководство пользователя страница 87

Страница: 87 / 110

Troubleshooting the System

Inc.

750.001.003

Revised June 1999

Check the Antennas and Cables for Continuity

Continuity is a direct connection or dead short between two points on
a cable. Continuity can expose bad cables or problems with
connections.

Step 1:

Turn off the power to the Reader.

Step 2:

Disconnect all the cables between the Reader, the ATU
and the antennas.

Step 3:

Check each cable for continuity. If continuity is present in a
cable, then the cable is shorted. Redo the cable.

Reception

The reception portion of the system should not exhibit continuity. If
continuity is found during any of the following steps, fill out the
Customer Support Questionnaire (page 107) and call Customer
Support at 1-800-577-6080.

Step 4:

Check the

connector on the Reader for continuity. If

there is continuity, then there is a problem with the
Reader.

Step 5:

Connect the coax cable from the

connector on the

Reader to the

Reader

connector on the ATU and

check for continuity in the

RX Antenna

connector. If there

is continuity, then there is a problem with the ATU.

Step 6:

Check the

connector on the antenna for continuity. If

continuity exists, then there is a problem with the antenna.

Step 7:

Connect the coax cable from the receiving antenna to the

RX Antenna

connector on the ATU. If there is continuity,

then there is a problem with the ATU.

Transmission

The transmission portion of the system should have continuity. If
continuity is not present, then follow the directions given for each
step.

Step 8:

Check the

connector on the Reader for continuity. If

continuity

does

not

exist, there is a problem with the

Reader. Fill out the Customer Support Questionnaire
(page 107) and call Customer Support at 1-800-577-6080.

Step 9:

Connect the coax cable to the

connector on the

Reader and check for continuity at the other end. If there is
no continuity, the cable is bad. Redo the cable.

Step 10:

Connect the other end of the coax cable to the

TX Reader

connector on the ATU and check for continuity in the

Antenna

connector. If continuity does not exist, then there

is a problem with the ATU. Fill out the Customer Support

Содержание NT132















































































































Результаты поиска

Содержание NT132

Отзывы:

Axcess NT132, Руководство по установке, Страница: 87 / 110

Результаты поиска

Содержание NT132

Отзывы: