Avtech AVR-EB4-B Скачать руководство пользователя | Manualshive

Страница: 9 / 83

background image

REGULATORY NOTES

FCC PART 18

This device complies with part 18 of the FCC rules for non-consumer industrial,
scientific and medical (ISM) equipment.

This instrument is enclosed in a rugged metal chassis and uses a filtered power entry
module (where applicable). The main output signal is provided on a shielded connector
that is intended to be used with shielded coaxial cabling and a shielded load. Under
these conditions, the interference potential of this instrument is low.

If interference is observed, check that appropriate well-shielded cabling is used on the
output connectors. Contact Avtech ([email protected]) for advice if you are unsure
of the most appropriate cabling. Also, check that your load is adequately shielded. It
may be necessary to enclose the load in a metal enclosure.

If any of the connectors on the instrument are unused, they should be covered with
shielded metal “dust caps” to reduce the interference potential.

This instrument does not normally require regular maintenance to minimize interference
potential. However, if loose hardware or connectors are noted, they should be
tightened. Contact Avtech ([email protected]) if you require assistance.

EC DECLARATION OF CONFORMITY

We

Avtech Electrosystems Ltd.
P.O. Box 5120, LCD Merivale
Ottawa, Ontario
Canada K2C 3H5

declare that this pulse generator meets the intent of Directive 2004/108/EG for
Electromagnetic Compatibility. Compliance pertains to the following specifications as
listed in the official Journal of the European Communities:

EN 50081-1 Emission

EN 50082-1 Immunity

9

«
...
7
8
9
10
11
...
»

Содержание AVR-EB4-B




















































































Отзывы:

Нет отзывов

Похожие инструкции для AVR-EB4-B

Бренд: Yamaha Страницы: 2

SMatrix DMX2400

Бренд: dallmeier Страницы: 12

Бренд: palintest Страницы: 14

Бренд: KROHNE Страницы: 34

Бренд: Unior Страницы: 2

Бренд: Vaisala Страницы: 83

Бренд: Endress+Hauser Страницы: 88

Бренд: PITSID Страницы: 22

Бренд: Swan Analytical Instruments Страницы: 102

Microlog GX Series

Бренд: SKF Страницы: 342

Бренд: Alfa Laval Страницы: 18

Бренд: ACE INSTRUMENTS Страницы: 6

Бренд: AKCP Страницы: 16

Бренд: Swann Страницы: 106

Бренд: Liquid Controls Страницы: 16

Бренд: SRS Labs Страницы: 11

Бренд: International Light Technologies Страницы: 19

ProScale 950 Series

Бренд: Accurate Technology Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды