SPECIFICATIONS
Model:
AVR-3-PW-TEK3-B
2
Basic Description:
High and low current "combo" pulser,
with GPIB / RS-232
Number of Outputs:
2
Output 1
Output 2
Amplitude (R
L
≥ 50 Ω)
3,4
:
10 to 250 V
10 to 50V
Amplitude accuracy:
Greater of ±2% or ±0.5V.
Provided termination:
50.0 ± 1%
Voltage rise & fall times:
≤ 10 ns (20%-80%)
≤ 0.5 ns (20%-80%)
Pulse width (FWHM):
250 ns to 250 us
50 to 200 ns
Droop (at max. pulse width):
≤ 2%
Overshoot (at max. amp.):
≤ 5%
PRF:
Internal trigger: 1 Hz to 10 kHz, External trigger: 0 Hz to 10 kHz
Duty cycle (max):
0.25%
0.2%
Polarity
5
:
Positive or negative (specify)
Propagation delay:
≤ 150 ns (Ext trig in to pulse out)
Jitter:
± 100 ps ± 0.03% of sync delay (Ext trig in to pulse out)
Output connector:
BNC
SMA
Probe attachment style:
Flexible clamping cable on output module
6
. The output module is
connected to the front panel by a 12" / 30 cm coaxial cable.
Trigger modes:
Internal trigger, external trigger (TTL-level pulse, > 10 ns, 1 kΩ input impedance),
front-panel “Single Pulse” pushbutton, or single pulse trigger via computer command.
Variable delay:
(Sync to main out)
0 to 1.0 seconds, for all trigger modes (including external trigger). Common to all outputs.
Sync output (will drive 50Ω):
+3 Volts, 100 ns
Gated operation:
Synchronous, active high or low, switchable.
GPIB and RS-232 control
2
:
Standard feature on all -B units.
Ethernet port, for remote
control using VXI-11.3, ssh,
telnet, & web:
Optional
7
. Recommended as a modern alternative to GPIB / RS-232.
See
http://www.avtechpulse.com/options/vxi
for details.
LabView drivers:
Check for available downloads at
http://www.avtechpulse.com/labview
.
Power requirements:
100 - 240 Volts, 50 - 60 Hz
Dimensions:
100 mm x 430 mm x 375 mm (3.9” x 17” x 14.8”)
Mounting:
Any. Add -R5 to the model number to add a rack-mount kit.
Temperature range:
+5°C to +40°C
1)
-C suffix indicates stand-alone lab instrument with internal clock and line powering. (See
http://www.avtechpulse.com/formats
for the basic instrument formats). Not
recommended for new designs. Use -B versions instead.
2)
-B suffix indicates IEEE-488.2 GPIB and RS-232 control of amplitude, pulse width, PRF and delay (See
http://www.avtechpulse.com/gpib
).
3)
For operation at amplitudes of less than 10% of full-scale, best results will be obtained by setting the amplitude near full-scale and using external attenuators on the
output.
4)
The amplitude of the AVR-3-PW-TEK2-C may also be controlled by a 0 to +10V DC voltage applied to a rear-panel BNC connector, in addition to the standard front-panel
controls.
5)
Indicate desired polarity by suffixing model number with -P or -N (i.e. positive or negative).
6)
An optional additional output module is available for "Output 2" of the AVR-3-PW-TEK3-B, which is suitable for use with CT-1 and CT-2 current probes. This output module
uses a very short length of de-solderable bus-bar wire (instead of flexible cable) which must be fed through the probe. Add the suffix "-CT" to the model number to specify
this option.
7)
Add the suffix -VXI to the model number to specify the Ethernet port.
7
Содержание AVR-3-PW-TEK3-B
