background image

Evolv DNA 200 

 

200 Watt Variable Power Module with Temperature Protection and USB 

Preliminary Datasheet 

The DNA 200 is a power regulated digital switch-mode DC-DC converter for personal vaporizers. 

It features Evolv’s patented Wattage Control, Temperature Protection, Preheat, Digital User Controls, 
OLED Screen, Onboard Buttons and Synchronous Rectification for maximum battery life and minimal 
heat generation. The DNA 200 runs from a 3 cell lithium polymer battery, and features cell-by-cell 
battery monitoring and integrated balance charger. The USB port and Evolv’s EScribe software can be 
used to customize or monitor the user experience. It is the most advanced personal vaporizer controller 
ever made.  

Specifications 

 

Minimum 

Typical 

Max 

Output Power 

1 Watt 

 

200 Watts 

Output Voltage 

1 Volt 

 

9.0 Volts 

Output Current, continuous 

 

 

50.0 Amps 

Output Current, instantaneous peak 

 

 

55.0 Amps 

Atomizer Resistance, temperature sensing wire, cold 

.08 Ohm 

.4 Ohm 

1.0 Ohm 

Atomizer Resistance, kanthal wire 

.08 Ohm 

.7 Ohm 

2.0 Ohms 

Temperature Limit 

200

°

450

°

600

°

Input Voltage 

9.0 Volts 

11.1 Volts 

12.6 Volts 

Input Current 

.5 Amps 

9.0 Amps 

23.0 Amps 

Screen On Current 

 

18mA 

 

Quiescent Current 

 

4.5 mA 

 

Power Down Current 

 

 

5uA 

Efficiency 

 

97% 

 

 

Summary of Contents for DNA 200
















Reviews: