manualshive.com logo in svg

Avidsen 114461, Руководство пользователя

Поделиться
Скачать
Avidsen 114461 Скачать руководство пользователя страница 47

EN

47

F - MAINTENANCE AND UPKEEP

1 - MAINTENANCE WORK

Maintenance work must be carried out by the 
installer or a qualified individual to guarantee the 
installation’s operation and safety.
The number of maintenance and upkeep operations 
must be proportional to the frequency the motorised 
gate is used.
For use of about 10 cycles per day, it is necessary 
to provide:

• 

Maintenance of the mechanical parts every 12 
months: tightening screws, lubrication, checking 
the rail, guides and gate balance, etc.

• 

Maintenance of the electronic parts every 6 
months: motor operation, photocells, control 
devices, etc.

2 - OPERATING INDICATORS

This system has two operating indicators: the battery 
charge level (optional) and the history of events.

&KDUJHEDWWHULH

KLVWRULTXHGHVpYqQHPHQWV

FGGBDF

IJTUPSJRVF

/

/

/

/

/

&RGH

/

/

/

/

/

&RGH

/

/

/

/

/

&RGH

/

/

/

/

/

&RGH

/

/

/

/

/

²

²

²

0(18

6(7

T

352*

6(7

6(7

6(7

 EFS

OJÒS

FFSS

FVS

delete

history

Battery charge

history of events

(last err

or)

3 - BATTERY VOLTAGE (FOR OPTIONAL 
SOLAR POWER KIT)

You can display the battery charge level.

• 

From

 

MENU 0

, 

press

 

“SET”

, and the battery 

charge level is then shown by the number of red 
LEDs lit.

• 

If the battery voltage level is too low (no LED on), 
the gate will not close in order to avoid closing off 
access.

CONNECTED MOTOR DRIVE KIT

Содержание 114461

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды