manualshive.com logo in svg

Avidsen 114461, Руководство пользователя

Поделиться
Скачать
Avidsen 114461 Скачать руководство пользователя страница 16

EN

16

C - INSTALLATION

4 - ATTACHING THE SET OF PHOTOCELLS

Important notes:
•  The photocells must be perfectly aligned and parallel to each other.
•  The reception photocells (RX is indicated at the back) must be installed at the same side of the 

gate as the geared motor.

For the exterior photocells:

The surface of the posts where the photocells will be attached must be perfectly flat in order to properly align 
the infrared beam of the photocells.
The photocells must be placed at a height of between 30 and 60cm from the ground.

30 cm min
60 cm max

outer side of the property

perfect alignment

10cm min/15cm

max

RX

view from above

outer side of the property

Mounting:
• 

Mount the photocells on the posts. 

• 

Open the photocells by removing the 2 screw covers and the 2 screws.

• 

Position the photocell in a vertical position in the location defined.

• 

Mark the position of the two fastening holes and the position of the hole for the cable to run through.

45mm

20mm

CONNECTED MOTOR DRIVE KIT

Содержание 114461

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды