Avia D 100 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 108

background image

O P E R A T I N G I N S T R U C T I O N S

40

During driving

n

It is not allowed to drive without the

engine running and the gear shifted.

n

Watch the indicator and warning

lights on the move from time to time.

n

If any of the warning lamp shown in

the  picture  above  comes  on  while  dri-
ving, it is necessary  to stop the vehicle
(at the soonest with regards to the traf-
fic circumstances  for the  sake  of safe-
ty). In addition, if the engine - stop light
comes  on,  it  is  also  necessary  to  shut

n

After the vehicle is set in motion,

check the efficiency of the service
brake.

Checking the braking efficiency

is  important  especially  in  winter,  after
washing  the  vehicle  or  after  fording
(passing  through  a  deeper  pool  of
water). Brake up the vehicle repeatedly
to allow a quick drying out of the brake
system.

n

Do not brake sharply - on one hand

the tires and brake system would be
worn quickly and too much, on the other
hand this way of braking would endan-
ger the other motorists.

n

Depress the accelerator pedal gra-

dually.

n

Depress the clutch pedal as far as it

goes.

n

Shift to gears smoothly not to stress

the engine extremely. Before engaging
the reverse run, put the vehicle to a full
stop not to cause damage to gearbox.

n

Before shifting to reverse gear at the

gearbox model ZF 6 S 850 it is neces-
sary to wait 3 to 5 seconds after depres-
sing the clutch pedal (to allow stopping
of shafts in gearbox) and only after that
engage the reverse gear.

the engine off.
Then proceed according to Chapter:

Troubleshooting

.

If the coolant temperature indicator light
comes on, it is necessary to reduce the
vehicle  speed,  to  downshift,  and  stop
the  vehicle  as  soon  as  possible  and
allow  cooling  down  the  engine  by  the
enhanced  speed  (1,200÷1,500  rpm).

Warning!

If the fuel reserve indicator light comes
on (item 1), it is  still about 16 l fuel in the
fuel  tank.
If  the yellow  control  light  ECAS*  starts
glowing, then the rear part of the vehicle
is  outside  the  driving  height  position
(level)  Applicable  for  version  with  pne-
umatick  suspension  only.

In any case it is not allowed to shut
the engine off when the coolant
temperature indicator light comes
on.

FN044cu

«
...
38
39
40
41
42
...
»

Содержание D 100













































































































Отзывы:

Нет отзывов

Похожие инструкции для D 100

Бренд: Uebler Страницы: 18

BLACK STEEL S2560

Бренд: Fab Fours Страницы: 9

Бренд: Barker Страницы: 2

Бренд: Alpine Страницы: 69

Бренд: Allen Sports Страницы: 2

Бренд: Romik Страницы: 6

Бренд: Ford Страницы: 22

Бренд: ideus Страницы: 159

Бренд: JKS Страницы: 3

Бренд: Simplicity Страницы: 10

Бренд: Guidosimplex Страницы: 8

Бренд: Mercedes-Benz Страницы: 10

Sprinter Bed System DIY

Бренд: FVC Страницы: 8

Бренд: Tesla Страницы: 42

Бренд: LaserLine Страницы: 4

Бренд: STO N SHO Страницы: 7

Бренд: Whispbar Страницы: 18

Бренд: Whispbar Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды