Avia D 100 Скачать руководство пользователя страница 27

Страница: 27 / 108

D E S C R I P T I O N

The belt strap must not be worn

over rigid or breakable objects,
which are stored in your clothing in
pockets.

Seat belts, which have been

subject to an accident or have
been damaged, must be uncon-
ditionally replaced with new ones.

Take care that the belt is not

twisted and is worn across pelvis
and not across soft parts of the
body if possible.

The maximum effect can be

reached only with a correct
seating position in cabin.

Do not strap in more than one

person with each belt.

Keep the seat belts clean (dirt

impairs the function of the
retractor). Use the soap water to
clean the seat belts.

If the seat belt has been dama-

ged, it is necessary to have it
replaced.

Warning!

Use of seat belts

The respective warning light reminds

you of necessity of the use of seat belts

Grasp the belt holding it at tongue

and slowly fit it across the chest and
pelvis.

The belt must fit snugly to the centre

of arm and to your pelvis.

If the belt locks when being pulled

out, release it, let it rewind and after that
pull it out again.

Insert the belt tongue into a

respective seat buckle. The belt is
anchored properly when it clicks into a
buckle.

To release the seat belt, press the

red marked cap on the buckle.

Seat belts height adjustment

Due to the height adjustable belt

anchorage, the belt can be adapted to
fit the body dimensions.

To adjust the belt height, push the

button  downwards,  tilt  the  upper
anchorage toward you (up) and  adjust
it  to  the  desired  position.

Содержание D 100













































































































Результаты поиска

Содержание D 100

Отзывы:

Похожие инструкции для D 100

Бренды по названию

Популярные бренды

Avia D 100, Руководство пользователя

Результаты поиска

Содержание D 100

Отзывы:

Похожие инструкции для D 100

Бренды по названию

Популярные бренды