Avia D 100 Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 108

background image

75

T R O U B L E S H O O T I N G

8. "Engine - stop" indicator light ON

Fault: Serious engine defect (it may be probably the
coolant temperature, charge air temperature or oil
pressure)

Remedy: Stop the vehicle and shut the engine off.
Carry  out  the  diagnostic  test  (the  diagnostic  procedure  is
mentioned on  the  following page).  If the  light code lights
up  during this test, there is a serious defect in the engine
and it is necessary to contact the authorized service
station. It is strictly prohibited  to continue to drive the
vehicle.  However, when  the  indicator  lights "engine  -  stop"
and  "engine  -  warning"  light  together  permanently  during
the diagnostic test, you can continue to drive the vehicle.

9. Indicator light "engine - warning" is ON

Fault: Fault in the engine system or in the engine
component and/or the AdBlue fluid volume drop in the
tank below 3 l

Remedy: Add the AdBlue fluid to tank. If the indicator
light  still  remains  ON,  you can  continue  to  operate  the
vehicle,  but  when  you  reach  ther  nearest  service
station,  have  the  fault  repaired  -  this  situation  is  not
considered  to  be  a  state  of  emergency.

Engine

10. Indicator light

"engine - warning" flashes

Fault: If the indicator light flashes for about 30
seconds when the ignition is in the position "ON". It
reminds you of carrying our the necessary service
job (e.g. the engine oil change) or it indicates the
presence of water in fuel

.

Remedy:  Drain  the  fuel  filter  according  to  Chapter
"Draining  the  fuel  filter".
If  the indicator  light  is  still ON,  it  is  necessary to  contact
the  authorized  service  station.
Note: After the oil has been changed do not forget to
store this action into the engine ECM  - have it carried
out by the  authorized repair shop.

11. Indicator light

" SCR system malfunction" is ON

Fault: The tank of AdBlue is empty

Remedy:  The  vehicle  may  be  still  operated,  but  when
you  reach  ther  nearest service  station,  have  the  fault
repaired  -  this  situation  is  not  considered  to  be  a  state
of  emergency.

«
...
73
74
75
76
77
...
»

Содержание D 100













































































































Отзывы:

Нет отзывов

Похожие инструкции для D 100

Бренд: Carcomm Страницы: 2

Бренд: Whispbar Страницы: 14

Бренд: Ford Страницы: 38

Бренд: U & Me Brothers Страницы: 6

Stratus LHD 1997

Бренд: Chrysler Страницы: 1534

Бренд: Würth Страницы: 36

Evo All THAR-FOR3

Бренд: Fortin Страницы: 7

Бренд: Fiat Страницы: 24

Бренд: Valeo Страницы: 28

Sedan CIVIC 2022

Бренд: Honda Страницы: 701

Бренд: MULTILIFT Страницы: 62

Бренд: Camoplast Страницы: 19

LED Dominator TAM83S2

Бренд: Whelen Engineering Company Страницы: 2

Бренд: EUFAB Страницы: 4

Бренд: QA1 Страницы: 3

Бренд: Edelbrock Страницы: 2

Бренд: Hudson Страницы: 77

Бренд: Metra Electronics Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды