AVGear AVG-CS4K-88-V2 Скачать руководство пользователя страница 1

Страница: 1 / 32

AVG-CS4K-88-V2

The AVG-

CS4K-88 V2 is a professional 4K HDBaseT

Distribution Matrix Kit, which consists of a 4K HDBaseT
Matrix Switcher, 7 HDBaseT Receivers and accessories.
This system is capable of being fully integrated into a
whole home control system solution.

Features



7 HDBaseT outputs, distances up to 70m at
1080p and 40m at 4Kx2K on a single CAT6. 1
HDMI output.



Supports HDMI 1.4 & HDCP 2.2, is compliant
with lower standards.



Transmits 4Kx2K @60Hz 4:2:0 signal for 8m via
HDMI port, 40m via HDBT ports.



Supports manual HDCP management and auto-
detection.



The HDBaseT Receivers are powered by the
matrix switcher via PoC technology.



LED indicators show real-time switching status.



Control via front panel, IR, RS232 and TCP/IP.



Supports bi-directional IR(5V) & RS232 control.



CEC control to far end displays via RS232
commands.



Built-in GUI for TCP/IP control.



Powerful EDID management.

Содержание AVG-CS4K-88-V2

































Результаты поиска

Содержание AVG-CS4K-88-V2

Отзывы:

Похожие инструкции для AVG-CS4K-88-V2

Бренды по названию

Популярные бренды

AVGear AVG-CS4K-88-V2, Руководство пользователя

Результаты поиска

Содержание AVG-CS4K-88-V2

Отзывы:

Похожие инструкции для AVG-CS4K-88-V2

Бренды по названию

Популярные бренды